Mita 412RE
| Код ошибки | Описание | ||
| C1 | Drive motor | ||
| C2 | Cleaning lamp / blanking lamps | ||
| C3 | Lens | ||
| C4 | Transfer/Separation corona | ||
| C5 | Scanner | ||
| C6 | Exposure lamp | ||
| C7 | Thermistor | ||
| C8 | Heat |
Mita 513Z
| Код ошибки | Описание | ||
| C01 | Toner sensor | ||
| C02 | Drum heater | ||
| C03 | Drum heater | ||
| C04 | Toner sensor | ||
| C05 | Data transfer | ||
| C06 | Board problem | ||
| C07 | Board problem | ||
| C21 | Drive motor/clock pulse | ||
| C22 | PF motor/clock pulse | ||
| C31 | Exposure lamp stays off | ||
| C32 | Exposure lamp stays on | ||
| C35 | Serve motor board/scan motor | ||
| C36 | Serve motor/clock pulse | ||
| C37 | Scan drive | ||
| C41 | Lens motor | ||
| C51 | Charge corona | ||
| C52 | Transfer/sep/corona | ||
| C53 | Bias below 125VDC | ||
| C55, C56, C58 | Drum potential | ||
| C61 | Heater M off | ||
| C62 | Heater M on | ||
| C63 | Heater S off | ||
| C64 | Heater S on | ||
| C65, C66 | Thermistor | ||
| C71 | Blank lamp/cleaning lamp |
C6 more than
|
Код ошибки |
Описание |
|
C1 |
Paper feed problem |
|
C3 |
Scanner problem |
|
C6 |
Heat problem |
|
PF |
C6 more than 6 times |
Mita 1205
|
Код ошибки |
Описание |
|
C3 |
Scan |
|
C6 |
Fuser |
Memory problem. Main board or
|
Код ошибки |
Описание |
|
AP |
CC50. Toner being mixed |
|
C01 |
Memory problem. Main board or simulation 70 required |
|
C02 |
EEPROM or main board |
|
C21 |
Drive problem (CC50/1256) |
|
C30 |
Scan |
|
C40 |
Lens drive |
|
C61 |
Fuser problem. No heat or open circuit |
|
C63 |
Fuser thermistor open |
|
C64 |
Fuser thermistor. Short or high fuser temperature |
|
C72 |
1256 drum thermistor open |
|
C73 |
1256 drum thermistor shorted |
|
C74 |
CC50/1256 Developer unit fuse. May have to replace developer unit. Problem at setup |
|
C74 |
1257 Developer thermistor |
|
C75 |
CC50/1256 Drum unit switch problem or drum setup problem |
|
C75 |
1257 developer thermistor |
|
C76 |
May not apply to CC50 or 1256, except if metric. Waste toner full. Reset with simulation 78 |
|
J01 |
Feed jam |
|
J02 |
Drum or fuser area jam |
|
J03 |
Jam |
|
OF |
1256 drum & developer units must be replaced |
|
OP |
Front door open |
|
PE/PF |
No paper, no paper feed problem |
|
U1 |
Total counter |
|
Ub |
CC50. Old developer unit and new drum. Can be reset by replacing the fuse, or by turning the drum one full revolution |
|
Uc |
CC50. New developer unit and old drum. On rear of drum is drum lock. Inside the opening is a white plastic that snaps down after the unit is installed. Remove this rear cover and snap the white plastic blocker back up |
|
UF |
Toner or developer not installed properly |
Memory problem. Main board or
|
Код ошибки |
Описание |
|
AP |
CC50. Toner being mixed |
|
C01 |
Memory problem. Main board or simulation 70 required |
|
C02 |
EEPROM or main board |
|
C21 |
Drive problem (CC50/1256) |
|
C30 |
Scan |
|
C40 |
Lens drive |
|
C61 |
Fuser problem. No heat or open circuit |
|
C63 |
Fuser thermistor open |
|
C64 |
Fuser thermistor. Short or high fuser temperature |
|
C72 |
1256 drum thermistor open |
|
C73 |
1256 drum thermistor shorted |
|
C74 |
CC50/1256 Developer unit fuse. May have to replace developer unit. Problem at setup |
|
C74 |
1257 Developer thermistor |
|
C75 |
CC50/1256 Drum unit switch problem or drum setup problem |
|
C75 |
1257 developer thermistor |
|
C76 |
May not apply to CC50 or 1256, except if metric. Waste toner full. Reset with simulation 78 |
|
J01 |
Feed jam |
|
J02 |
Drum or fuser area jam |
|
J03 |
Jam |
|
OF |
1256 drum & developer units must be replaced |
|
OP |
Front door open |
|
PE/PF |
No paper, no paper feed problem |
|
U1 |
Total counter |
|
Ub |
CC50. Old developer unit and new drum. Can be reset by replacing the fuse, or by turning the drum one full revolution |
|
Uc |
CC50. New developer unit and old drum. On rear of drum is drum lock. Inside the opening is a white plastic that snaps down after the unit is installed. Remove this rear cover and snap the white plastic blocker back up |
|
UF |
Toner or developer not installed properly |
Memory problem. Main board or
|
Код ошибки |
Описание |
|
AP |
Toner being mixed |
|
C01 |
Memory problem. Main board or simulation 70 required |
|
C02 |
EEPROM or main board |
|
C21 |
Drive problem |
|
C30 |
Scan, motor, switch |
|
C40 |
Lens drive |
|
C61 |
Fuser problem. No heat or open circuit |
|
C63 |
Fuser thermistor open |
|
C64 |
Fuser thermistor open |
|
C72 |
Drum thermistor open. Blank lamps |
|
C73 |
Drum thermistor shorted |
|
C74 |
Developer thermistor |
|
C75 |
Drum unit switch problem or drum setup problem |
|
C76 |
Waste toner full, reset with simulation 78 |
|
J01 |
Feed jam |
|
J02 |
Drum or fuser area jam |
|
J03 |
Jam |
|
OF |
Drum & developer units must be replaced (entire process unit) |
|
OP |
Front door open |
|
PE/PF |
No paper or paper feed problem |
|
U1 |
Total counter |
|
Ub |
Old developer unit and new drum. Might be upset by replacing the fuse, or by turning the drum through one full revolution |
|
Uc |
New developer unit and old drum. On rear drum is a lock. Inside the opening is a white plastic that snaps down after the unit is installed. Remove this rear cover and snap the white plastic blocker back up |
|
UF |
Toner or developer not installed properly. Bad toner sensor |
Fuser problem. Temperature too low,
|
Код ошибки |
Описание |
|
C3 |
Scan problem |
|
C6 |
Fuser problem. Temperature too low, too high, open thermistor. Heat lamp, thermofuse, thermistor, etc |
|
PE |
Paper empty |
Battery or main board. Simulation
|
Код ошибки |
Описание |
|
C01 |
Battery or main board. Simulation 70 might clear |
|
C30 |
Scan problem |
|
C31 |
Scan problem |
|
C32 |
Scan reverse problem |
|
C40 |
Lens motor |
|
C5 |
Lamp Problem |
|
C61 |
Low fuser temperature. Heat lamp, thermofuse |
|
C62 |
Low fuser temperature |
|
C63 |
Fuser thermistor |
|
C64 |
High fuser temperature. Triac, pinched wire |
|
C73 |
Shorted DV unit thermistor |
|
PE |
Paper empty |
Battery or main board. Simulation
|
Код ошибки |
Описание |
|
C01 |
Battery or main board. Simulation 70 might clear |
|
C30 |
Scan problem |
|
C31 |
Scan problem |
|
C32 |
Scan reverse problem |
|
C40 |
Lens motor |
|
C61 |
Low fuser temperature. Heat lamp, thermofuse |
|
C62 |
Low fuser temperature |
|
C63 |
Fuser thermistor |
|
C64 |
High fuser temperature. Triac, pinched wire |
|
C73 |
Shorted DV unit thermistor |
|
PE |
Paper empty |
Scan problem. Scan sensors, scan
|
Код ошибки |
Описание |
|
C01 |
NVRAM problem |
|
C20 |
Main drive problem |
|
C30 |
Scan problem. Scan sensors, scan motor, belt tension, cable tension, etc |
|
C40 |
Lens motor problem, lens sensor motor |
|
C50 |
Corona problem: Broken wire, shorted blocks, bad corona, high voltage transformer |
|
C61 |
Low fuser temperature. Problem with heat lamp, connections, thermal switch, thermistor or main board |
|
C63 |
Open fuser thermistor |
|
C64 |
Shorted fuser thermistor |
|
C72 |
Open drum thermistor |
|
C73 |
Shorted drum thermistor |
|
C74 |
Open external thermistor |
|
C75 |
Shorted external thermistor |
|
C90 |
Communication problem between copier and ADF |
|
J30 |
Jam in registration area |
|
J40 |
Jam inside machine or fuser |
|
J50 |
Exit jam or fuser jam |
|
PF |
Paper feed |
Lens motor or mirror
|
Код ошибки |
Описание |
|
C01 |
Memory |
|
C20 |
Drive |
|
C30 |
Scan |
|
C31 |
Scan return |
|
C32 |
Scan motor |
|
C33 |
Scan motor brake |
|
C40 |
Lens motor or mirror motor |
|
C50 |
Charge corona |
|
C51 |
T/S corona |
|
C60 |
High temperature |
|
C61 |
Fuser thermistor |
|
C62 |
No warm up |
|
C63 |
Fuser temperature drops |
|
C70 |
Drum thermistor short |
|
C71 |
Drum thermistor open |
Mita 1655
|
Код ошибки |
Описание |
|
C2 |
Drive section |
|
C4 |
Lens unit |
|
C5 |
Corona |
|
C6 |
Heater |
Memory loss. Use simulation 70
|
Код ошибки |
Описание |
|
AP |
Toner is mixing |
|
C01 |
Memory loss. Use simulation 70 to try and repair. Otherwise must replace main board |
|
C21 |
Main drive problem |
|
C31 |
Scan problem |
|
C41 |
Lens problem |
|
C42 |
Mirror motor problem |
|
C51 |
Charge corona problem |
|
C52 |
Transfer corona problem |
|
C61 |
Low fuser temperature. Lamp, thermofuse, connections, etc |
|
C63 |
Fuser thermistor |
|
C64 |
Fuser thermistor short |
|
C72 |
Drum thermistor |
|
C73 |
Drum thermistor short |
|
LED (orange) |
Paper feed motor problem, or sensor |
|
LED (orange,flashing) |
ADF interlock |
|
LED (red) |
ADF open sensor |
|
OP |
Front door open of optional cassette is open |
|
U1 |
Key counter |
front door interlocks switches
| Код ошибки | Описание |
| C2 | Drive problem |
| C3 | Scan problem |
| C4 | Lens problem |
| C5 | Coronas |
| C6 | Heater problem or only 1 of the 2 front door interlocks switches is actuated |
| C0 | Main board problem Run simulation 90. Try power off/on |
Communication problem between main board
|
Код ошибки |
Описание |
|
AP |
Toner is feeding |
|
C01 |
Backup memory problem |
|
C03 |
Communication problem between main board and scan drive board |
|
C05 |
Ground problem having to do with main board and power relay. Possible short |
|
C07 |
Operation panel thermistor is shorted. Scan motor |
|
C21 |
Main drive problem |
|
C22 |
Side to side registration motor problem in duplex unit |
|
C23 |
Desk drive motor drive problem |
|
C24 |
Paper deck paper conveying motor |
|
C31 |
Scan problem. Scan sensors, scan motor, scan motor drive board, belt tension, cable tension |
|
C41 |
Lens motor problem |
|
C42 |
Scan mirror problem |
|
C51 |
Charge corona problem |
|
C52 |
Transfer/separator corona problem |
|
C61 |
Low fuser temperature |
|
C63 |
Open fuser thermistor |
|
C64 |
Shorted drum thermistor |
|
C72 |
Open drum thermistor |
|
C73 |
Shorted drum thermistor |
|
C81 |
Sorter/stapler feed motor drive problem |
|
C82 |
Sorter/stapler bin shift motor problem |
|
C83 |
Sorter/stapler guide bar motor or guide bar motor sensor |
|
C84 |
Sorter/stapler slide motor problem or sensor problem |
|
C91 |
RADF original feed motor drive problem; motor, pulse sensor, etc |
|
C92 |
RADF belt drive motor drive problem; motor pulse sensor, RADF main board |
|
C93 |
RADF loop motor problem. Loop motor, pulse sensor or RADF main board |
|
OP |
Cover or door open |
|
PF |
Paper feed |
|
U1 |
Key counter missing |
Original on document feeder placed
|
Код ошибки |
Описание |
|
AF |
Original on document feeder placed wrong |
|
C00 |
Battery problem or main board |
|
C01 |
Battery problem or main board |
|
C2 |
Drive problem |
|
C20 |
Drive problem |
|
C21 |
Duplex side to side registration |
|
C3 |
Scan |
|
C4 |
Lens motor |
|
C40 |
Lens motor |
|
C41 |
Mirror motor |
|
C5 |
Coronas |
|
C6 |
Low fuser temperature |
|
C60 |
High fuser temperature |
|
C61 |
Low fuser temperature |
|
C7 |
DV unit shift problem; color unit dip switch; bad fuser thermofuse |
|
C70, C71 |
DV unit shift problem; color unit dip switch; bad fuser thermofuse |
|
U1 |
Key counter |
|
UF |
Color unit out |
Paper feed problem
|
Код ошибки |
Описание |
|
C1 |
Paper feed problem (more than 6 times = PF) |
|
C2 |
Drive |
|
C3 |
Scanner problem |
|
C5 |
Corona |
|
C6 |
Heat problem (Fuser) |
|
H0 |
Battery problem |
|
U1 |
Key counter |
Original on document feeder placed
|
Код ошибки |
Описание |
|
AF |
Original on document feeder placed wrong |
|
C00 |
Battery problem or main board |
|
C01 |
Battery problem or main board |
|
C2 |
Drive problem |
|
C20 |
Drive problem |
|
C21 |
Duplex side to side registration |
|
C3 |
Scan |
|
C4 |
Lens motor |
|
C40 |
Lens motor |
|
C41 |
Mirror motor |
|
C5 |
Coronas |
|
C6 |
Low fuser temperature |
|
C60 |
High fuser temperature |
|
C61 |
Loe fuser temperature |
|
C7 |
DV unit shift problem; color unit dip switch; bad fuser thermofuse |
|
C70, C71 |
DV unit shift problem; color unit dip switch; bad fuser thermofuse |
|
U1 |
Key counter |
|
UF |
Color unit out |
Communication problem between main board
|
Код ошибки |
Описание |
|
AP |
Toner is feeding |
|
C01 |
Backup memory problem |
|
C03 |
Communication problem between main board and scan drive board |
|
C05 |
Ground problem having to do with main board and power relay. Possible short |
|
C07 |
Operation panel thermistor is shorted. Scan motor |
|
C21 |
Main drive problem |
|
C22 |
Side to side registration motor problem in duplex unit |
|
C23 |
Desk drive motor drive problem |
|
C24 |
Paper deck paper conveying motor |
|
C31 |
Scan problem. Scan sensors, scan motor, scan motor drive board, belt tension, cable tension |
|
C41 |
Lens motor problem |
|
C42 |
Scan mirror problem |
|
C51 |
Charge corona problem |
|
C52 |
Transfer/separator corona problem |
|
C61 |
Low fuser temperature |
|
C63 |
Open fuser thermistor |
|
C64 |
Shorted drum thermistor |
|
C72 |
Open drum thermistor |
|
C73 |
Shorted drum thermistor |
|
C81 |
Sorter/stapler feed motor drive problem |
|
C82 |
Sorter/stapler bin shift motor problem |
|
C83 |
Sorter/stapler guide bar motor or guide bar motor sensor |
|
C84 |
Sorter/stapler slide motor problem or sensor problem |
|
C91 |
RADF original feed motor drive problem; motor, pulse sensor, etc |
|
C92 |
RADF belt drive motor drive problem; motor pulse sensor, RADF main board |
|
C93 |
RADF loop motor problem. Loop motor, pulse sensor or RADF main board |
|
OP |
Cover or door open |
|
PF |
Paper feed |
|
U1 |
Key counter missing |
Heat problem or fuser
|
Код ошибки |
Описание |
|
C1 |
Back up battery |
|
C2 |
Back up memory |
|
C20 |
Drive |
|
C31 |
Scan (Reset by unplugging) |
|
C40 |
Lens motor |
|
C50 |
Charge corona |
|
C51 |
T/S corona |
|
C60 |
High fuser temp |
|
C61 |
Heat problem or fuser switches |
|
C62 |
Heat problem |
|
C63 |
Low temperature |
|
C70 |
DV selector |
|
C01 |
Back up battery |
|
C02 |
Back up memory |
|
C05 |
Drum thermistor |
Heat problem or fuser
|
Код ошибки |
Описание |
|
C1 |
Back up battery |
|
C2 |
Back up memory |
|
C20 |
Drive |
|
C31 |
Scan (Reset by unplugging) |
|
C40 |
Lens motor |
|
C50 |
Charge corona |
|
C51 |
T/S corona |
|
C60 |
High fuser temp |
|
C61 |
Heat problem or fuser switches |
|
C62 |
Heat problem |
|
C63 |
Low temperature |
|
C70 |
DV selector |
|
CO1 |
Back up battery |
|
CO2 |
Back up memory |
|
CO5 |
Drum thermistor |
Memory loss, main board, etc.
|
Код ошибки |
Описание |
|
C01 |
Memory loss, main board, etc. Do simulation 70 |
|
C03 |
Communication problem between main board and scan, or bad scan board or main board |
|
C21 |
Main drive problem |
|
C22 |
Desk side to side registration motor problem |
|
C23 |
Desk drive problem |
|
C31 |
Scan problem |
|
C41 |
Lens problem |
|
C51 |
Charge corona problem |
|
C52 |
Transfer/separator corona problem |
|
C61 |
Fuser problem. SSR |
|
C63 |
Fuser thermistor |
|
C64 |
Fuser temperature too high |
|
C65 |
Fuser temperature too low |
|
C71 |
Developer thermistor |
|
C72 |
Drum thermistor open |
|
C73 |
Drum thermistor short |
|
OP |
Door open |
|
U1 |
Key counter |
Multiple sheets in feed
|
Код ошибки |
Описание |
|
J020 |
Paper deck horizontal jam |
|
J021 |
Paper deck horizontal jam |
|
J022 |
Paper deck horizontal jam |
|
J023 |
Converging section jam |
|
J024 |
Multiple sheets in feed section |
|
J025 |
Multiple sheets in vertical section |
|
J026 |
Multiple sheets in duplex |
|
J027 |
Multiple sheets before registration |
|
J030 |
Registration or transfer area jam |
|
J040 |
Fuser jam |
|
J050 |
Exit jam |
|
J051 |
Feed shift jam |
|
J060 |
Duplex jam |
|
J070 |
No original fed by RADF |
|
J071 |
RADF jam |
|
J072 |
RADF belt area jam |
|
J073 |
RADF loop section jam |
|
J074 |
RADF exit jam |
|
J080 |
Copier to sorter jam |
|
J081 |
Sorter feed in jam |
|
J082 |
Jam in non sort bin |
|
J083 |
Non sort exit jam |
|
J084 |
Sorter conveyor jam |
|
J085 |
Sorter exit jam |
|
J090 |
Post sorter jam |
|
J091 |
Stacker hand section jam |
Exposure lamp stays
|
Код ошибки |
Описание |
|
30 |
Exposure lamp/XL thermofuse |
|
32 |
Exposure lamp stays on |
|
C1 |
Back up battery |
|
C2 |
Back up memory |
|
C20 |
Drive |
|
C31 |
Scan (Reset by unplugging) |
|
C40 |
Lens motor |
|
C50 |
Charge corona |
|
C51 |
T/S corona |
|
C60 |
High fuser temp |
|
C61 |
Heat prob./fuser switch |
|
C62 |
Heat problem |
|
C63 |
Low temperature |
|
C70 |
DV selector |
|
CO1 |
Back up battery |
|
CO2 |
Back up memory |
|
CO5 |
Drum thermistor |
Battery on main board. May
|
Код ошибки |
Описание |
|
C01 |
Battery on main board |
|
C02 |
Battery on main board. May be reset with simulation 70 |
|
C05 |
Drum thermistor. May be reset with simulation 49 |
|
C20 |
Drive problem (pulse sensor, broken gear, bind etc.) |
|
C21 |
Side registration motor or switch problem (duplex area?) |
|
C30 |
Exposure lamp problem or Auto exposure sensor |
|
C31 |
Scan problem |
|
C40 |
Lens motor problem |
|
C41 |
Mirror motor problem |
|
C50 |
Charge corona |
|
C51 |
Transfer/separator corona |
|
C60 |
High fuser temperature, or shorter thermistor |
|
C61 |
Open thermistor |
|
C62 |
Open heater lamp. Not sure if this Код ошибки would light for open thermosfuse or low heat |
Side to side switch in
|
Код ошибки |
Описание |
|
C01, C02 |
Battery problem. Try simulation 70 |
|
C03 |
Serial communication (main board) |
|
C05 |
Drum thermistor |
|
C20 |
Drive problem |
|
C21 |
Side to side switch in duplex unit |
|
C22 |
Suction fan |
|
C30 |
Exposure lamp |
|
C31 |
Scan drive |
|
C40 |
Lens drive |
|
C41 |
Mirror drive |
|
C50 |
Charge corona |
|
C51 |
Transfer/separator corona |
|
C60 |
High fuser temperature |
|
C61 |
Open fuser thermistor |
|
C62 |
Low fuser temperature |
Communication problem between main board
|
Код ошибки |
Описание |
|
C01 |
Memory problem. Use simulation 70 |
|
C03 |
Communication problem between main board and scan board |
|
C05 |
Auxiliary CPU ROM on main board |
|
C21 |
Main drive problem |
|
C22 |
Duplex side to side registration motor problem |
|
C23 |
Desk drive problem |
|
C24 |
Suction motor |
|
C31 |
Scan problem |
|
C41 |
Lens problem |
|
C51 |
Charge corona short |
|
C52 |
Transfer/separator corona short |
|
C61 |
Fuser problem. Low temperature or open circuit |
|
C63 |
Fuser problem. Thermistor |
|
C64 |
Fuser problem. High temperature |
|
C65 |
Fuser problem. Low temperature or open circuit |
|
C72 |
Drum thermistor open |
|
C73 |
Drum thermistor shorted |
|
C74 |
Developer unit thermistor open |
|
C81 |
Sorter paper feed motor |
|
C82 |
Sorter bin motor |
|
C83 |
Stapler jam |
|
C84 |
Sort bin problem |
|
C85 |
Sorter table motor |
|
C86 |
Sorter bin slide motor |
|
C87 |
Sorter paperweight motor |
|
C88 |
Sorter jogger motor |
|
C89 |
Punch jam |
|
C91 |
RADF feed motor |
|
C92 |
RADF transport motor |
|
C93 |
RADF loop motor |
|
C94 |
RADF motor running too fast |
|
C95 |
RADF loop motor running too fast |
Mita 4085
|
Код ошибки |
Описание |
|
C2 |
Drive |
|
C30 |
Scan |
|
C31 |
Exposure lamp |
|
C4 |
Lens motor |
|
C50 |
T/S corona |
|
C51 |
Charge corona |
|
C60 |
Thermistor |
|
C61 |
Heater |
|
C7 |
Blank lamp |
|
C8 |
Sorter |
Communication problem between main board
|
Код ошибки |
Описание |
|
C01 |
Memory problem. Use simulation 70 |
|
C03 |
Communication problem between main board and scan board |
|
C05 |
Auxiliary CPU ROM on main board |
|
C21 |
Main drive problem |
|
C22 |
Duplex side to side registration motor problem |
|
C23 |
Desk drive problem |
|
C24 |
Suction motor |
|
C31 |
Scan problem |
|
C41 |
Lens problem |
|
C51 |
Charge corona short |
|
C52 |
Transfer/separator corona short |
|
C61 |
Fuser problem. Low temperature or open circuit |
|
C63 |
Fuser problem. Thermistor |
|
C64 |
Fuser problem. High temperature |
|
C65 |
Fuser problem. Low temperature or open circuit |
|
C72 |
Drum thermistor open |
|
C73 |
Drum thermistor shorted |
|
C74 |
Developer unit thermistor open |
|
C81 |
Sorter paper feed motor |
|
C82 |
Sorter bin motor |
|
C83 |
Stapler jam |
|
C84 |
Sort bin problem |
|
C85 |
Sorter table motor |
|
C86 |
Sorter bin slide motor |
|
C87 |
Sorter paperweight motor |
|
C88 |
Sorter jogger motor |
|
C89 |
Punch jam |
|
C91 |
RADF feed motor |
|
C92 |
RADF transport motor |
|
C93 |
RADF loop motor |
|
C94 |
RADF motor running too fast |
|
C95 |
RADF loop motor running too fast |
Multiple sheets in feed
|
Код ошибки |
Описание |
|
J020 |
Paper deck horizontal jam |
|
J021 |
Paper deck horizontal jam |
|
J022 |
Paper deck horizontal jam |
|
J023 |
Converging section jam |
|
J024 |
Multiple sheets in feed section |
|
J025 |
Multiple sheets in vertical section |
|
J026 |
Multiple sheets in duplex |
|
J027 |
Multiple sheets before registration |
|
J030 |
Registration or transfer area jam |
|
J040 |
Fuser jam |
|
J050 |
Exit jam |
|
J060 |
Duplex jam |
|
J070 |
No original fed by RADF |
|
J071 |
RADF jam |
|
J072 |
RADF belt area jam |
|
J073 |
RADF loop section jam |
|
J074 |
RADF exit jam |
|
J080 |
Copier to sorter jam |
|
J081 |
Sorter feed in jam |
|
J082 |
Jam in non sort bin |
|
J083 |
Non sort exit jam |
|
J084 |
Sorter conveyor jam |
|
J085 |
Sorter exit jam |
|
J090 |
Post sorter jam |
|
J091 |
Stacker hand section jam |
Duplex side to side registration
|
Код ошибки |
Описание |
|
C01 |
Battery |
|
C02 |
Memory |
|
C03 |
Main board or eject board |
|
C05 |
Drum thermistor |
|
C20 |
Drive |
|
C21 |
Duplex side to side registration motor/switches |
|
C30 |
Exposure lamp/thermofuse |
|
C31 |
Scan |
|
C40 |
Lens motor |
|
C41 |
Mirror motor |
|
C50 |
Charge corona |
|
C51 |
Transfer/separator |
|
C60 |
High fuser temperature |
|
C61 |
Fuser thermistor |
|
C62 |
Low temperature |
Side to side switch in
|
Код ошибки |
Описание |
|
C01, C02 |
Battery problem. Try simulation 70 |
|
C03 |
Serial communication (main board) |
|
C05 |
Drum thermistor |
|
C20 |
Drive problem |
|
C21 |
Side to side switch in duplex unit |
|
C22 |
Suction fan |
|
C30 |
Exposure lamp |
|
C31 |
Scan drive |
|
C40 |
Lens drive |
|
C41 |
Mirror drive |
|
C50 |
Charge corona |
|
C51 |
Transfer/separator corona |
|
C60 |
High fuser temperature |
|
C61 |
Open fuser thermistor |
|
C62 |
Low fuser temperature |
With the main switch on,
|
Код ошибки |
Описание |
|
C01 |
Battery problem. Try simulation 70 |
|
C01 |
Backup battery problem-- With the main switch on, the back up battery voltage is lower than 2.8V |
|
C02 |
Backup memory problem--Backup memory is faulty |
|
C02 |
Battery problem. Try simulation 70 |
|
C03 |
Serial communication (main board) |
|
C03 |
Serial communication problem--Less than 10 serial data signals are input into and output from the main PCB every 50ms |
|
C05 |
Drum thermistor problem--The drum thermistor output voltage is out of the range between 0.3 and 4.7V |
|
C05 |
Drum thermistor |
|
C20 |
Drive problem--More than 20 clock pulses are not input to the main PCB within 1 s after the drive motor has turned on |
|
C20 |
Drive problem |
|
C21 |
Side to side switch in duplex unit |
|
C21 |
Side registration motor problem--The side registration switch fails to turn on within 8 s after the main switch has turned on |
|
C22 |
Suction fan |
|
C22 |
Paper conveying section fan motor problem--CN1-5 on the BM detection PCB remains high |
|
C30 |
Exposure lamp |
|
C30 |
Broken halogen lamp wire--The AE sensor output does not exceed 4 V within 300 ms after the HL REMOTE signal has applied to the AVR/Output PCB |
|
C31 |
Scan drive |
|
C40 |
Lens drive |
|
C40 |
Lens motor problem--The lens home position switch fails to turn on within 8 s after the main switch has turned on |
|
C41 |
Mirror motor problem--The mirror home position switch fails to turn on within 8 s after the main switch has turned on |
|
C41 |
Mirror drive |
|
C50 |
Main high voltage problem |
|
C50 |
Charge corona |
|
C51 |
Transfer, separation high voltage problem |
|
C51 |
Transfer/separator corona |
|
C60 |
High fuser temperature |
|
C60 |
Abnormally high temperature in the fixing section--The fixing unit thermistor output voltage remains less than 0.5 V for longer than 1 s, indicating the fixing temperature rises above 536F |
|
C61 |
Open fuser thermistor |
|
C61 |
Broken fixing unit thermistor wire--The fixing unit thermistor wire--The fixing unit thermistor output voltage exceeds 4.9 V |
|
C62 |
Broken fixing unit heater wire--Fixing temperature does not reach 329 F within 4 minutes after the power relay has turned on |
|
C62 |
Low fuser temperature |
Scan motor or scan motor
|
Код ошибки |
Описание |
|
C05 |
Communication problem between main boards |
|
C06 |
Battery/memory problem |
|
C21 |
Main motor drive |
|
C22 |
Duplex motor drive |
|
C23 |
Paper feed motor drive |
|
C24 |
Duplex motor drive |
|
C25 |
Paper feed motor drive |
|
C31 |
Open exposure lamp |
|
C32 |
Exposure lamp stays on |
|
C35 |
Scan motor or scan motor board or fuser |
|
C37 |
Scan sensor not actuated or not deactuated at proper time |
|
C41 |
Lens motor |
|
C51 |
Charge corona |
|
C52 |
Transfer/separator corona |
|
C53 |
Bias is less then 100 volts |
|
C55 |
Drum surface voltage is too high |
|
C56 |
Drum surface voltage is too low |
|
C61 |
Fuser lamp closest to exit end stays off |
|
C62 |
Fuser lamp closest to drum stays off |
|
C63 |
Fuser lamp(s) stays on |
|
C65 |
High fuser temperature |
|
C66 |
Open fuser thermistor |
|
C71 |
Blank lamp problem |
|
C72 |
Drum thermistor shorted |
|
C73 |
Drum thermistor open |
|
C74 |
High DV unit temperature or shorted DV thermistor |
|
C75 |
Open DV thermistor |
Scan motor or scan motor
|
Код ошибки |
Описание |
|
C05 |
Communication problem between main boards |
|
C06 |
Battery/memory problem |
|
C21 |
Main motor drive |
|
C22 |
Duplex motor drive |
|
C23 |
Paper feed motor drive |
|
C24 |
Duplex motor drive |
|
C25 |
Paper feed motor drive |
|
C31 |
Open exposure lamp |
|
C32 |
Exposure lamp stays on |
|
C35 |
Scan motor or scan motor board or fuser |
|
C37 |
Scan sensor not actuated or not deactuated at proper time |
|
C41 |
Lens motor |
|
C51 |
Charge corona |
|
C52 |
Transfer/separator corona |
|
C53 |
Bias is less then 100 volts |
|
C55 |
Drum surface voltage is too high |
|
C56 |
Drum surface voltage is too low |
|
C61 |
Fuser lamp closest to exit end stays off |
|
C62 |
Fuser lamp closest to drum stays off |
|
C63 |
Fuser lamp(s) stays on |
|
C65 |
High fuser temperature |
|
C66 |
Open fuser thermistor |
|
C71 |
Blank lamp problem |
|
C72 |
Drum thermistor shorted |
|
C73 |
Drum thermistor open |
|
C74 |
High DV unit temperature or shorted DV thermistor |
|
C75 |
Open DV thermistor |
Drum potential sensor or no
|
Код ошибки |
Описание |
|
C05 |
Circuit board problem |
|
C06 |
Battery problem. Try simulation 79 |
|
C07 |
Ram problem |
|
C21 |
Drive problem-upper section |
|
C22 |
Drive problem-lower section |
|
C23 |
Paper feed motor |
|
C24 |
Duplex side registration sensor (jogger) or motor |
|
C25 |
Large capacity cassette |
|
C26 |
Fuser motor |
|
C31 |
Open exposure lamp |
|
C32 |
Exposure lamp won't shut off |
|
C35 |
Scan motor scan board |
|
C41 |
Lens motor |
|
C51 |
Charge corona |
|
C52 |
Transfer/separator corona |
|
C53 |
Bias problem |
|
C54 |
Drum potential sensor |
|
C55 |
Drum potential sensor |
|
C56 |
Drum potential sensor or no charge |
|
C62 |
Fuser problem. Low heat. Lamp (there are 2) or thermofuse |
|
C63 |
Fuser lamps won't shut off |
|
C65 |
High fuser temperature or shorted fuser thermistor |
|
C66 |
Open fuser thermistor |
|
C71 |
Blank lamp problem |
|
C72 |
Shorted drum thermistor |
|
C73 |
Shorted DV unit thermistor |
|
C74 |
Shorted DV unit thermistor |
|
C75 |
Open DV unit thermistor |
The specified data was not
|
Код ошибки |
Описание |
|
C010 |
Backup memory problem-- The specified data was not written into NVRAM |
|
C030 |
Serial communication problem (main PCB problem)--Communication procedure fails to complete within 200 ms in any block. Nine consecutive reception errors occur in one block |
|
C031 |
Serial communication problem (operation unit PCB problem)--Communication procedure fails to complete within 200 ms in any block. Nine consecutive reception errors occur in one block |
|
C032 |
Serial communication problem (servo motor PCB problem)--serial communication between the main PCB and the servo motor PCB fails five times consecutively |
|
C033 |
Serial communication problem (RDH main PCB problem)--Serial communication between the copier main PCB and the RDH main PCB fails five times consecutively |
|
C110 |
Halogen lamp problem--While the scanner motor rotates in forward direction because of the lamp on signal, the HLISENS input signal fails to go low. The HLISENS input signal fails to go low during exposure correction |
|
C210 |
Paper conveying motor problem--No enКод ошибкиr signal is received 250 ms after the paper conveying motor on signal has been emitted |
|
C220 |
Side registration motor problem--The side registration home position switch fails to turn on within 5 s after the main switch has been turned on |
|
C230 |
Fewer than five pulses are generated by the drum motor enКод ошибкиr in 1 s after the drum motor on signal has been emitted |
|
C240 |
Paper deck motor problem--The paper deck level switch or the home position switch fails to turn on within 20 s after the paper deck motor on signal has been emitted |
|
C250 |
Upper drawer motor problem--The upper drawer level switch or the position switch fails to turn on within 8 s |
|
C251 |
Middle drawer motor problem--The middle drawer level switch or the position switch fails to turn on within 8 s after the middle drawer motor on signal has been emitted |
|
C252 |
Lower drawer motor problem--The lower drawer level switch or the position switch fails to turn on within 8 s after the middle drawer motor on signal has been emitted |
|
C310 |
Scanner motor problem (main PCB problem)--The home position switch fails to turn on within 4 s after the scanner motor reverse signal has been emitted |
|
C311 |
Scanner motor problem (servo motor PCB problem)--No signal is generated by the enКод ошибкиr 20ms after the scanner motor reverse signal has been emitted |
|
C312 |
Scanner motor problem3523 or more SM forward pulses are received after the scanner motor has started to rotate forward. The scanner motor speed exceeds the specified level |
|
C313 |
The home position switch fails to turn on within 4 s after the SM HP signal has gone low |
|
C314 |
Servo motor CPU problem--With the scanner motor forward signal on, the average motor speed exceeds 900 mm/s in any 60 ms (excluding the first 20 ms after the signal is emitted;or with the scanner motor reverse signal on, the average motor speed exceeds 1600 mm/s in any 60 ms excluding the first 60 ms after the signal is emitted |
|
C410 |
Lens motor problem--The lens home position switch fails to turn on within 12 s after the lens motor home signal has been emitted |
|
C510 |
Main high voltage problem--The short detection signal is generated by the main charger high-voltage PCB for 5 s |
|
C520 |
Transfer high voltage problem--The transfer high voltage short detection signal is generated by the transfer charger high-voltage PCB for 5 s |
|
C521 |
Separation high-voltage problem--The separation high voltage short detection signal is generated by the transfer charger high-voltage PCB for 5 s |
|
C530 |
Pre-transfer high-voltage problem--The pre-transfer short detection signal is generated by the pretransfer charger high-voltage PCB for 5 s |
|
C540 |
Bias problem-The short detection signal is generated by the bias PCB for 5 s |
|
C550 |
Potential sensor problem--During initial potential sensor calibration, the difference between the sensor outputs when 500 V and 300 V are applied to the drum is zero or negative |
|
C560 |
Potential adjustment problem: max level--During initial potential settling, the drum potential cannot be set to the specified level by increasing the primary main charger control signal to its maximum |
|
C561 |
Potential adjustment problem: min. level--During initial potential setting, the drum potential cannot be set to the specified level by reducing the primary admin charger control signal to its minimum |
|
C570 |
Exposure adjustment problem: max level-- |
|
C571 |
Exposure adjustment problem: min level--During initial light intensity correction, the potential sensor output cannot be set to the specified level even with the halogen lamp control signal at min |
|
C610 |
Fixing unit heater M wire broken--No heater check signal is generated by the noise filter PCB 800 ms after the fixing unit heater S off signal and the fixing unit heater M on signal have been emitted |
|
C611 |
Fixing unit heater S wire broken--No heater check signal is generated by the noise filter PCB 800 ms after the fixing unit heater M off signal and the fixing unit heater S on signal have been emitted |
|
C620 |
Fixing unit heats failing to turn off--The heater check signal continues to be generated by the noise filter PCB 320 ms after the fixing unit heater M and S off signals have been emitted |
|
C630 |
Fixing unit thermistor wire broken--The data generated by the fixing unit thermistor remains at F1H or above for longer than two minutes while fixing unit heaters M and S are on |
|
C640 |
Fixing unit thermistor wire shorted/abnormally high temperature detected--Data from the fixing unit thermistor remains at 45H or less for 160 ms or longer |
|
C641 |
Fixing unit thermistor abnormally low temperature detected--The signal from the fixing unit thermistor registers 100C or lower during standby or a copying cycle after secondary stabilization |
|
C710 |
Toner sensor problem--Data from the toner sensor remains at 14H or less, or F0H or above for 320 ms |
|
C720 |
Drum thermistor wire broken--The signal from the drum thermistor remains high for 5 s |
|
C730 |
Drum thermistor shorted/abnormally high temperature detected--The signal from the drum thermistor remains low for 5 s |
|
C731 |
Drum thermistor abnormally low temperature detected--The drum heater remains on at 100% output for 17 minutes with the safety switches on |
|
C740 |
Internal temperature thermistor broken--Data from the internal temperature thermistor remains at 0CH or less for 320 ms |
|
C741 |
External temperature thermistor problem--Data from the external temperature thermistor remains at F0H or above (too low a temperature or broken wire) or at 33H or less (too high a temperature or shorted wire) for 320 ms |
|
C750 |
Developing unit thermistor problem--Data from the developing unit thermistor remains at F0H or above (too low a temperature or broken wire) or at 33H or less (too high a temperature or shorted wire) for 320 ms |
|
C760 |
Toner cartridge shutter problem--The shutter home position switch fails to turn off within 10 s after the toner cartridge a shutter mode on signal has been emitted. The shutter home position switch fails to turn on within 40 s after it has turned off |
|
C761 |
Toner cartridge loading problem--The TCPSW1 or TCPSW2 signal falls to be input within 40 s after the toner cartridge loading motor on signal has been emitted |
|
C762 |
Toner hopper problem--No signal is input from the toner level detection switch after automatic toner replenishing is completed |
|
C810 |
Sorter feed motor problem--A feed motor problem--A feed motor jam is detected (with the stapler-sorter attached). The feed motor current exceeds 2 A for 50 ms (with the sorter attached) |
|
C811 |
Sorter feed motor circuit problem--No feed motor index signal is detected for 30 ms (with the sorter attached) |
|
C820 |
Sorter bin drive motor problem--The sorter bin unit fails to return to the home position during initialization (with the stapler-sorter attached). The sorter shift motor current exceeds 1.2 A for 50 ms (with the sorter attached) |
|
C821 |
Sorter shift motor PCB problem (sorter)--No enКод ошибкиr signal is detected from the sorter shift motor for 50 ms |
|
C830 |
Sorter table motor problem (stapler-sorter)--The sorters stapler table fails to return to the home position during initialization |
|
C831 |
Sorter bin side motor problem (stapler-sorter)--The bin fails to return to the sliding home position during initialization. The bin fails to move to the stapling/punching position. The bin fails to return to the sliding home position |
|
C832 |
Sorter paper weight motor problem (stapler-sorter)--The sorter paper weight fails to return to the home position during initialization. The sorter paper weight fails to move to the operating position when it should. The sorter paper weight fails to return to the home position after releasing the paper |
|
C833 |
Sorter jog motor problem--The jog unit fails to return to the home position during initialization. The job unit fails to move to the standby position when paper is fed |
|
C840 |
Sorter bin upper limit detected (stapler-sorter)--The bin upper limit sensor turns on while the sorter bin drive motor drives |
|
C841 |
Sorter bin unit lower limit detected (stapler-sorter)--The bin unit lower limit sensor turns on while the sorter bin drive motor drives |
|
C850 |
Sorter punch jam (stapler-sorter)--The punch fails to return to the home position during initialization. The punch fails to return to the home position during operation |
|
C851 |
Sorter stapler jam--The stapler fails to return to the home position during initialization. The stapler fails to return to the home position during operation. The stapler motor current exceeds 5 A for 30 ms (with the sorter) |
|
C852 |
Sorter stapler motor problem--A block signal fails to be input from the home sensor within 100 ms after the stapler motor has turned on. Home signal fails to be input within 250 ms after the block signal has been emitted |
|
C860 |
Sorter shutter motor problem (auto stacker)--The sorter shutter fails to close during initialization. The sorter shutter fails to close during initialization. The sorter shutter fails to open during operation. The sorter shutter fails to close during operation |
|
C861 |
Hand table motor problem (auto stacker)--The hand table fails to return to the home position during initialization. The hand table fails to return to the home position during initialization. The hand table fails to move to the standby position during operation. The hand unit fails to move to the standby position during operation. The hand unit fails to return to the home position for paper ejection |
|
C862 |
Hand unit drive motor problem (auto stacker)--The hand unit fails to return to the home position during initialization. The hand table fails to return to the home position during initialization. The hand table fails to move to the standby position during operation. The hand unit fails to move to the standby position during operation. The hand unit fails to return to the home position for paper ejection |
|
C863 |
Stapler-sorter-stacker communication problem--An error occurs during serial communication between the stapler-sorter and the auto-stacker |
|
C910 |
RDH original feed motor problem--No pulse is generated by the pulse sensor for 800 ms or longer while the RDH original feed motor is rotating |
|
C920 |
RDH original conveying motor problem--No pulses are generated by the pulse sensor for 800 ms or longer while the RDH original conveying motor is rotating. No pulses are generated by the pulse sensor for 800 ms or longer while the RDH original conveying motor is rotating |
|
C930 |
RDH original eject motor problem--No pulse is generated by the pulse sensor for 800 ms or longer while the RDH original eject motor is rotating |
|
C940 |
RDH original transfer motor problem--If the original transfer plate home position switch fails to turn on during the 2.5 s when the original transfer motor reverses for 2.5 s, which is repeated twice. The home position switch does not turn on after this process |
|
C950 |
RDH original jogging motor problem--If the RDH original jogging guide home position switch fails to turn off 1 s or longer after the original jogging motor has turned on |
Drum potential sensor or no
|
Код ошибки |
Описание |
|
C05 |
Circuit board problem |
|
C06 |
Battery problem. Try simulation 79 |
|
C07 |
Ram problem |
|
C21 |
Drive problem-upper section |
|
C22 |
Drive problem-lower section |
|
C23 |
Paper feed motor |
|
C24 |
Duplex side registration sensor (jogger) or motor |
|
C25 |
Large capacity cassette |
|
C26 |
Fuser motor |
|
C31 |
Open exposure lamp |
|
C32 |
Exposure lamp won't shut off |
|
C35 |
Scan motor scan board |
|
C41 |
Lens motor |
|
C51 |
Charge corona |
|
C52 |
Transfer/separator corona |
|
C53 |
Bias problem |
|
C54, C55 |
Drum potential sensor |
|
C56 |
Drum potential sensor or no charge |
|
C62 |
Fuser problem. Low heat. Lamp (there are 2) or thermofuse |
|
C63 |
Fuser lamps won't shut off |
|
C65 |
High fuser temperature or shorted fuser thermistor |
|
C66 |
Open fuser thermistor |
|
C71 |
Blank lamp problem |
|
C72 |
Shorted drum thermistor |
|
C73, C74 |
Shorted DV unit thermistor |
|
C75 |
Open DV unit thermistor |
Не берет бумагу излотка ручной
1. Заменить муфту подачи.
2. Или плохо срабатывает микрик в узле захвата.
http://www.repair-printer.ru/viewtopic.php?t=4956
и контакты на всех платах
Перебрал все клеммы и контакты на всех платах и пошло все.
http://www.repair-printer.ru/viewtopic.php?t=4841
в сервисное меню принтера. Для
Сбросить пасмперс можно войдя в сервисное меню принтера. Для входа в сервисный режим:
1. Выключить принтер.
2. Нажать и удерживая кнопку RESUME, включить принтер кнопкой POWER и удерживать ее.
3. Отпустить кнопку RESUME, а затем нажать и отпустить кнопку RESUME еще 2 раза. (кнопку POWER все еще нужно удерживать нажатой).Все. Теперь Вы в сервисном режиме.
Нажимая кнопку RESUME определенное количество раз, можно выбрать необходимое действие:
(например если нажать кнопку RESUME 4 раза - будет произведен сброс счетчика отработанных чернил - "памперса")
1 нажатие - service/factory test printout, including ink sensor check
2 нажатия - EEPROM info printout
3 нажатия - EEPROM initialization
4 нажатия - Clear the waste-ink counter
5 нажатий - Printer model setting. (more selections beyond this- leave this alone)
После выбора нужной операции необходимо нажать кнопку POWER для завершения действия.
После повторного нажатия кнопки POWER принтер выключится и будет готов к новому включению с уже измененными настройками.
Если печатающая головка принтера вышла из строя, то в сервисном режиме индикатор будет все время мигать и сброс памперса не поможет решить эту проблему.
http://www.repair-printer.ru/viewtopic.php?t=4499
Оригинальные и поддельные картриджи
В настоящее время на рынке расходных материалов появилась лавина картриджей, поддельных под оригинал. Что из себя представляет подделка? В двух словах: отмытый химией старый картридж, заправленный тонером, и упакованный в новую коробку. На примере картриджа CANON E-30 для аппаратов серии FC/PC мы покажем примерную себестоимость этого картриджа у производителя подделок:
1. Скупка картриджей у населения. Цена картриджа ~ 200 рублей (~7,2 $). Цены, которые указаны в прайс-листе, фирмы скупающей картриджи несколько завышены и конечная цена зависит от состояния картриджа. И если сотрудник, скупающий картриджи, найдет хоть одну черточку или точку на фотобарабане этого картриджа цена опустится значительно. Поэтому мы берем среднюю цену
2. Далее следует процесс разборки и отмывки картриджа, полировки фотобарабана. Себестоимость данного процесса составляет не более 100 рублей (~3,5 $).
3. Следующая стадия это заправка картриджа и его сборка. Этот этап обходится в 150 рублей (~5,5 $).
4. И последний этап это упаковка картриджа в пластиковый пакет, фиксирующие картонные распорки и полноцветную коробку. Цена процесса и материалов тоже не превышает 100 рублей (~3,5 $)
Таким образом, себестоимость картриджа CANON E-30 (FC/PC) составляет не более 25$ (с учетом амортизации оборудования и других расходов при хорошем потоке производства).
Розничная цена данного картриджа 105$. Как правило, поддельные картриджи продаются естественно по более низкой, привлекательной цене ~85-95 $. Из этого следует, что данный бизнес приносит такой фирме до 250 % прибыли.
Теперь Вы имеете представление о том насколько, Вы, как покупатель расходных материалов, можете быть обмануты.
Какие выходы из данной ситуации? Выходов всего три:
1. Покупка оригинальных картриджей только в серьезных фирмах и магазинах, где цена картриджа будет, безусловно, выше на 10-15% (120$)
2. Покупка совместимого картриджа. Совместимый картридж это такой же старый картридж, заправленный и восстановленный, но продающийся в отличной от оригинала коробке и по более низкой цене (80$).
3. Заправка Вашего картриджа. Эта процедура продлит жизнь картриджа, никаким образом не повлияет на работу аппарата и принесет Вам серьезную экономию (23$ с выездом мастера). Если Вы еще сомневаетесь в надежности заправки картриджей, Вы можете посетить вебсайты мировых производителей материалов для индустрии регенерации (заправки и восстановления) картриджей и наглядно убедится, насколько серьезно развита эта индустрия в мире: www.scc-inc.com, www.lgchem.com, www.uninetimaging.com, www.futuregraphicsllc.com.
Сервис-центр ДЖЕСТ: (095) 580-29-90 (многоканальный) - www.kcepokc.ru
Заправка картриджей, ремонт копиров и лазерных принтеров, продажа цветных тонеров.
http://www.repair-printer.ru/viewtopic.php?t=537
От чего зависит быстрота износа фотобарабана в лазерных картриджах?
Качество бумаги - чем лучше бумага, тем дольше служит фотобарабан
Плотность бумаги - чем плотнее бумага, тем больше воздействие на фотобарабан и тем меньше служит фотобарабан
Покрытие бумаги - как правило, глянцевая бумага не подходит для печати с совместимым фотобарабаном. Тонер просто плохо "держится" на этой бумаге и налипает на фотобарабан, от чего тот загрязняется. Проблему можно решить постоянной чисткой фотобарабана.
Интенсивность печати - чем интенсивнее используется картридж, тем быстрее изнашивается фотобарабан
Использование стикеров - стикеры создают излишнюю нагрузку на фотобарабан, надо использовать специальные стикеры для лазерной печати.
Использование фирменных бланков - многие фирмы используют фирменные бланки (отпечатанные на цветном принтере или в типографии) - так же, как и стикер, создают дополнительную нагрузку на фотобарабан, тем более что дополнительная нагрузка приходится постоянно на одни и те же области фотобарабана.
Использование "обороток" (листов чистых с одной стороны) - лист проходит по фотобарабану своей использованной стороной, от чего барабан быстрее изнашивается
Культура пользователя - надо следить за принтером, вовремя проводить чистку и профилактику, не нагружать больше заявленной производельности.
По материалам: www.zapravka4u.ru
http://www.repair-printer.ru/viewtopic.php?t=2773
Отработка - это мусор, или нормальный тонер?
Отработка это = мусор+тонер+...=фон по листу жуткий, смерть картриджа, жуткое состояние принтера.
http://www.repair-printer.ru/viewtopic.php?t=4871
Scanner not
|
Код ошибки |
Описание |
|
E0 |
Fuser problem |
|
E1 |
Drive |
|
E2 |
Scanner not home |
|
E3 |
Paper feed |
|
E5 |
Forward scan |
|
E6 |
Timing |
|
E7 |
Paper transport |
|
E8 |
Drum installation |
Duplex or overlay selected with
|
Код ошибки |
Описание |
|
E00 |
Low fuser temperature |
|
E01 |
No 24VDC |
|
E02 |
No 10VDC |
|
E03 |
Charge corona |
|
E04 |
Trans/separator corona |
|
E05 |
Scan/scan home |
|
E06 |
Optics lens sensor |
|
E07 |
Copy ratio solenoid |
|
E08 |
AE out of specs |
|
E09 |
Logic problem |
|
E10 |
Scan speed |
|
E11 |
Main board |
|
E13 |
Sorter |
|
E16 |
Drive |
|
E17 |
Lens focus rank |
|
E25 |
24v problem in duplex unit |
|
E27 |
Duplex width sensor |
|
E28 |
Duplex length sensor |
|
E29 |
Duplex paper sensor |
|
U0 |
Key counter |
|
U4 |
Sorter |
|
U5 |
Duplex |
|
U6 |
Exit cover open |
|
U7 |
Duplex cover |
|
U9 |
Duplex or overlay selected with wrong paper size |
Panasonic 1310R
| Код ошибки | Описание | ||
| C10 | Key counter | ||
| E0 | Fuser problem | ||
| E1 | Drive | ||
| E2 | Scanner not home | ||
| E3 | Paper feed | ||
| E5 | Forward scan | ||
| E6 | Timing | ||
| E7 | Paper transport | ||
| E8 | Drum installation | ||
| J1 | Jam | ||
| U1 | Door |
Duplex or overlay selected with
|
Код ошибки |
Описание |
|
E00 |
Low fuser temperature |
|
E01 |
No 24VDC |
|
E02 |
No 10VDC |
|
E03 |
Charge corona |
|
E04 |
Trans/separator corona |
|
E05 |
Scan/scan home |
|
E06 |
Optics lens sensor |
|
E07 |
Copy ratio solenoid |
|
E08 |
AE out of specs |
|
E09 |
Logic problem |
|
E10 |
Scan speed |
|
E11 |
Main board |
|
E13 |
Sorter |
|
E16 |
Drive |
|
E17 |
Lens focus rank |
|
E25 |
24v problem in duplex unit |
|
E27 |
Duplex width sensor |
|
E28 |
Duplex length sensor |
|
E29 |
Duplex paper sensor |
|
U0 |
Key counter |
|
U4 |
Sorter |
|
U5 |
Duplex |
|
U6 |
Exit cover open |
|
U7 |
Duplex cover |
|
U9 |
Duplex or overlay selected with wrong paper size |
