The heater film has gone
|
Код ошибки |
Описание |
|
E0 |
Heater problem |
|
E1 |
The heater film has gone off center. Turn machine off & on, make sure it's level etc. |
|
E2 |
Scan problme |
|
E6 |
Exposure lamp or exposure lamp sensor |
Canon 10, 24, 115, 14, NP112, PC3
|
Код ошибки |
Описание |
|
E0 |
Heat lamp |
|
E2 |
Scanner |
Fuser problem. Low temperature. Lamp,
|
Код ошибки |
Описание |
|
E2 |
Scanner |
|
E0 |
Heat lamp |
|
D030 |
Total counter or DC controller |
|
E00 |
Heater (Press SW301 twice to reset) |
|
E001 |
Over temperature |
|
E010 |
Drum drive clock pulse |
|
E202 |
Scan home position |
|
E204 |
Registration switch (scan problem) |
|
E210 |
Lens home |
|
E221 |
Lamp regulator or DC controller |
|
E400 |
Document feed problem (Check circuit breaker) |
|
E500 |
Sorter (Check circuit breaker) |
|
E000 |
Fuser problem. Low temperature. Lamp, thermal switch, AC driver |
|
E001 |
Fuser problem. High temperature. Triac, AC driver, pinched wire |
|
E004 |
Fuser problem |
|
E053 |
Sorter |
|
E030 |
Counter |
|
E202 |
Scan |
|
E210 |
Lens |
|
E221 |
Exposure lamp regulator board, thermal fuse, exposure lamp |
|
E400 |
ADF |
|
E500 |
Sorter |
|
E710 |
DC controller (main board) |
|
E001 |
Heater problem |
thermoswitch or heat
|
Код ошибки |
Описание |
|
E0 |
Thermistor/ thermoswitch or heat lamps |
|
E1 |
Sorter |
|
E2 |
Scanner home |
|
E3 |
Scanner return |
|
E4 |
Right front door/main motor |
|
E5 |
Lens home |
|
E6 |
Lamp regulator |
|
E8 |
Counter wire |
High fuser temperature. Shorter fuser
|
Код ошибки |
Описание |
|
E0 |
Thermistor, thermal switch, heat |
|
E1 |
Sorter, scanner home |
|
E2 |
Motor, clock pulse |
|
E3 |
Scan problem |
|
E4 |
Lens home |
|
E5 |
Lamp regulator/document sensor |
|
E6 |
Motor control |
|
E7 |
Total counter |
|
E8 |
Lamp regulator |
|
E9 |
Copyboard drive motor/board |
|
ED |
Motor control PCB |
|
EE |
DC controller on motor |
|
E001 |
High fuser temperature. Shorter fuser thermistor |
|
E030 |
Total counter disconnected or open |
|
E202 |
Scan problem |
|
E210 |
Lens problem |
|
E221 |
DC power supply, lamp regulator board or main board |
|
E400 |
Document feeder board problem |
|
E500 |
Sorter board problem |
|
E000 |
Low fuser temperature |
DC controller on
|
Код ошибки |
Описание |
|
E0 |
Thermistor, thermal switch, heat |
|
E1 |
Sorter, scanner home |
|
E2 |
Motor, clock pulse |
|
E3 |
Scan problem |
|
E4 |
Lens home |
|
E5 |
Lamp regulator/document density sensor |
|
E6 |
Motor control board |
|
E7 |
Total counter |
|
E8 |
Lamp regulator |
|
E9 |
Copyboard drive motor/board |
|
ED |
Motor control PCB |
|
EE |
DC controller on motor |
Canon 210, 300
|
Код ошибки |
Описание |
|
E0 |
Heat problem |
|
E1 |
Sorter |
|
E2 |
Scanner |
|
E4 |
Drum drive |
|
E5 |
Lens drive |
|
E6 |
Exposure lamp |
|
E7 |
Mirror sensors |
Clock pulse or open RF
|
Код ошибки |
Описание |
|
E0 |
Fuser |
|
E1 |
Sorter |
|
E2 |
Scan home |
|
E3 |
Scan |
|
E4 |
Clock pulse or open RF door |
|
E5 |
Lens position |
|
E6 |
Exposure lamp, fuse 2 |
|
E8 |
Counter |
No problem. Means that the
|
Код ошибки |
Описание |
|
C |
No problem. Means that the machine is correcting the fuser film tracking |
|
CC |
Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier |
|
E000 |
Low fuser temperature |
|
E001 |
High fuser temperature |
|
E002 |
High fuser temperature |
|
E003 |
Erratic fuser temperature |
|
E007 |
Fuser film off track and will not repair itself |
|
E010 |
Main drive problem |
|
E030 |
Counter problem |
|
E064 |
Scan problem, or power supply |
|
E202 |
Scan problem |
|
E210 |
Lens drive problem or lens sensor |
|
E220 |
Exposure lamp stays on or off |
|
E240 |
DC controller (main board) or composite power supply |
|
E261 |
Zero cross problem. Power frequency or composite power supply |
|
E400 |
Communication problem between boards |
|
E803 |
24 volt problem |
|
E0 |
Fuser problem |
|
H |
Fuser overheat |
High fuser temperature. Shorter fuser
|
Код ошибки |
Описание |
|
E001 |
High fuser temperature. Shorter fuser thermistor |
|
E030 |
Total counter disconnected or open |
|
E202 |
Scan problem |
|
E210 |
Lens problem |
|
E221 |
DC power supply, lamp regulator board or main board |
|
E400 |
Document feeder board problem |
|
E500 |
Sorter board problem |
|
E000 |
Low fuser temperature |
Total counter or DC
|
Код ошибки |
Описание |
|
D030 |
Total counter or DC controller |
|
E00 |
Heater (Press SW301 twice to reset) |
|
E001 |
Over temperature |
|
E010 |
Drum drive clock pulse |
|
E202 |
Scan home position |
|
E204 |
Registration switch (scan problem) |
|
E210 |
Lens home |
|
E221 |
Lamp regulator or DC controller |
|
E400 |
Document feed problem (Check circuit breaker) |
|
E500 |
Sorter (Check circuit breaker) |
Fuser problem. Low temperature. Lamp,
|
Код ошибки |
Описание |
|
E000 |
Fuser problem. Low temperature. Lamp, thermal switch, AC driver |
|
E001 |
Fuser problem. High temperature. Triac, AC driver, pinched wire |
|
E004 |
Fuser problem |
|
E0053 |
Sorter |
|
E030 |
Counter |
|
E202 |
Scan |
|
E210 |
Lens |
|
E221 |
Exposure lamp regulator board, thermal fuse, exposure lamp |
|
E400 |
ADF |
|
E500 |
Sorter |
|
E710 |
DC controller (main board) |
Main motor, motor board, clock
|
Код ошибки |
Описание |
|
E000 |
Fuser problem |
|
E010 |
Main motor, motor board, clock pulse |
|
E030 |
Counter |
|
E050 |
Duplex side to side problem |
|
E051 |
Crossway registration |
|
E200 |
Scan problem |
|
E200 |
Scan reverse sensor or scan |
|
E202 |
Scan return problem |
|
E204 |
Document sensor, scan reverse sensor or scale |
|
E210 |
Lens problem |
|
E220 |
Lens |
|
E220 |
Blank lamp open or lens home problem |
|
E240 |
DC controller |
|
E400 |
Document feeder board problem or document feeder interface problem |
|
E500 |
Sorter |
|
E620 |
Editing problem |
Fuser temp low. Heat lamp,
|
Код ошибки |
Описание |
|
E000 |
Fuser temp low. Heat lamp, thermoswitch, thermistor, SSR |
|
E001 |
Fuser temperature too high or shorted thermistor |
|
E002 |
Fuser temperature too low |
|
E003 |
Fuser temperature too low |
|
E004 |
SSR, or lamp reg. board |
|
E010 |
Drive problem |
|
E022 |
DV unit switching problem |
|
E030 |
Counter not working/open |
|
E202 |
Scan problem. Scan sensor, scan motor |
|
E204 |
Scan problem. Scan sensor, scan motor |
|
E210 |
Lens problem. Lens sensor, lens motor |
|
E220 |
Exposure lamp |
|
E240 |
DC controller (main board) |
|
E400 |
RDF circuit board |
|
E401 |
RDF pickup motor drive |
|
E402 |
RDF belt motor drive |
|
E403 |
RDF feed drive problem |
|
E404 |
RDF exit motor |
|
E411 |
RDF sensor problem |
|
E500 |
Sorter board problem |
|
E510 |
Sorter feed motor |
|
E512 |
Sorter delivery motor |
|
E514 |
Sorter delivery motor |
|
E520 |
Sort stack motor |
|
E530 |
Vibrator motor |
|
E531 |
Stapler motor |
|
E535 |
Vibrator motor |
|
E540 |
Shift problem |
|
E541 |
Shift problem |
|
E710 |
DC controller |
|
E711 |
DC controller |
|
E712 |
DC controller. Document feeder board or cable |
|
E800 |
Auto shut off relay |
Blank lamp open or lens
|
Код ошибки |
Описание |
|
E000 |
Fuser problem |
|
E010 |
Drive |
|
E030 |
Counter |
|
E050 |
Duplex side to side problem |
|
E051 |
Duplex side to side problem |
|
E200 |
Scan problem |
|
E202 |
Scan return problem |
|
E204 |
Scan |
|
E210 |
Lens problem |
|
E220 |
Blank lamp open or lens home problem |
|
E240 |
Bad DC controller |
|
E400 |
Document feeder board problem or document feeder interface problem |
|
E500 |
Sorter |
|
E620 |
Editing problem |
Low fuser temperature. Heat lamp,
|
Код ошибки |
Описание |
|
E000 |
Low fuser temperature. Heat lamp, thermoswitch, thermofuse, thermistor, SSR |
|
E001 |
High fuser temperature. Thermistor, SSR, pinched wire |
|
E002 |
Low fuser temperature. Same as E002 |
|
E003 |
Same as E000/E001 |
|
E010 |
Same as E002 |
|
E022 |
Motor drive problem |
|
E030 |
Counter |
|
E202 |
Scan motor, sensor |
|
E204 |
Scan motor, sensor |
|
E210 |
Lens motor, sensor |
|
E220 |
Exposure lamp |
|
E240 |
DC controller (main board) |
|
E401 |
Pickup drive problem (might be Doc. Feeder) |
|
E402 |
Document belt drive problem |
|
E404 |
Exit motor (document feeder) |
|
E411 |
Document sensor (document feeder) |
|
E500 |
Sorter/machine communication problem |
|
E510 |
Sorter drive problem |
|
E530 |
Sorter home sensor |
|
E531 |
Stapler unit swing sensor |
|
E540 |
Sorter cam sensor |
|
E541 |
Sorter cam sensor |
|
E710 |
DC controller (main board) |
|
E712 |
DC controller or document feeder board |
Main motor, motor board, clock
|
Код ошибки |
Описание |
|
E000 |
Fuser problem |
|
E010 |
Main motor, motor board, clock pulse |
|
E030 |
Counter |
|
E050 |
Duplex side to side problem |
|
E051 |
Crossway registration |
|
E200 |
Scan problem |
|
E202 |
Scan return problem |
|
E202 |
Scan home sensor or home scan |
|
E204 |
Document sensor, scan reverse sensor or scale |
|
E210 |
Lens |
|
E220 |
Blank lamp open or lens home problem |
|
E240 |
DC controller |
|
E400 |
Document feeder board problem or document feeder interface problem |
|
E500 |
Sorter |
|
E620 |
Editing problem |
Low fuser temperature. Heat lamp,
|
Код ошибки |
Описание |
|
E000 |
Low fuser temperature. Heat lamp, thermoswitch, thermofuse, thermistor, SSR |
|
E001 |
High fuser temperature. Thermistor, SSR, pinched wire |
|
E002 |
Low fuser temperature. Same as E002 |
|
E003 |
Same as E000/E001 |
|
E010 |
Same as E002 |
|
E022 |
Motor drive problem |
|
E030 |
Counter |
|
E202 |
Scan motor, sensor |
|
E204 |
Scan motor, sensor |
|
E210 |
Lens motor, sensor |
|
E220 |
Exposure lamp |
|
E240 |
DC controller (main board) |
|
E401 |
Pickup drive problem (might be Doc. Feeder) |
|
E402 |
Document belt drive problem |
|
E404 |
Exit motor (document feeder) |
|
E411 |
Document sensor (document feeder) |
|
E500 |
Sorter/machine communication problem |
|
E510 |
Sorter drive problem |
|
E530 |
Sorter home sensor |
|
E531 |
Stapler unit swing sensor |
|
E540 |
Sorter cam sensor |
|
E541 |
Sorter cam sensor |
|
E710 |
DC controller (main board) |
|
E712 |
DC controller or document feeder board |
Bind or load on main
|
Код ошибки |
Описание |
|
E000 |
Low fuser temperature |
|
E001 |
High fuser temperature |
|
E010 |
Main motor clock pulse |
|
E011 |
Bind or load on main motor |
|
E020 |
No TF for 3 minutes |
|
E030 |
Copy counter |
|
E050 |
Duplex unit |
|
E201 |
Scan motor |
|
E203 |
Scan motor |
|
E210 |
Lens home |
|
E240 |
DC controller |
|
E241 |
DC controller |
|
E320 |
CCD |
|
E400 |
DC controller, 24V |
|
E500 |
DC controller, 24V |
|
E510 |
Finisher feed motor |
|
E520 |
Stacker motor |
|
E530 |
Guide plate shift motor |
|
E531 |
Stapler motor |
|
E620 |
DC controller, edit board |
High fuser temperature or shorter
|
Код ошибки |
Описание |
|
E000 |
No fuser heat |
|
E001 |
High fuser temperature or shorter thermistor |
|
E002 |
Low temperature or bad thermistor |
|
E003 |
Fuser problem |
|
E004 |
Bad SSR (heat staying on) |
|
E010 |
Drive |
|
E020 |
Black toner motor |
|
E030 |
Counter |
|
E080 |
Interface problem with color unit |
|
E081 |
Vertical drive motor |
|
E082 |
Horizontal drive motor |
|
E083 |
Color unit sensor on right |
|
E084 |
Color unit sensor on left |
|
E085 |
Color unit release sensor or release or solonoid |
|
E086 |
Color unit claw release |
|
E089 |
Laser problem |
|
E100 |
Laser problem |
|
E110 |
Laser motor |
|
E140 |
Laser |
|
E202 |
Scan |
|
E203 |
Scan |
|
E204 |
Scan |
|
E210 |
Lens |
|
E223 |
Color unit filter drive motor |
|
E240 |
DC controller |
|
E401 |
RDF pickup motor |
|
E402 |
RDF belt motor |
|
E403 |
RDF feed motor |
|
E411 |
RDF document sensor |
|
E500 |
Sorter-Copier communication error |
|
E510 |
Sorter drive |
|
E512 |
Sorter drive |
|
E513 |
Sorter drive |
|
E514 |
Sorter drive |
|
E520 |
Top limit sensor or stack sensor |
|
E530 |
Sorter home sensor |
|
E531 |
Stapler home sensor |
|
E535 |
Stapler swing sensor |
|
E540 |
Stack shift sensor |
|
E660 |
IC card |
|
E710 |
DC controller |
|
E711 |
DC controller |
|
E714 |
DC controller |
|
E800 |
Power off circuit |
Bind or load on main
|
Код ошибки |
Описание |
|
E00 |
Low fuser temperature |
|
E001 |
High fuser temperature |
|
E010 |
Main motor clock pulse |
|
E011 |
Bind or load on main motor |
|
E020 |
No TF for 3 minutes |
|
E030 |
Copy counter |
|
E050 |
Duplex unit |
|
E201 |
Scan motor |
|
E203 |
Scan motor |
|
E210 |
Lens home |
|
E240 |
DC controller |
|
E241 |
DC controller |
|
E320 |
CCD |
|
E400 |
DC controller, 24V |
|
E500 |
DC controller, 24V |
|
E510 |
Finisher feed motor |
|
E520 |
Stacker motor |
|
E530 |
Guide plate shift motor |
|
E531 |
Stapler motor |
|
E620 |
DC controller, edit board |
Sorter to DC control interface
|
Код ошибки |
Описание |
|
E000 |
Low fuser temperature |
|
E001 |
High fuser temperature |
|
E002 |
Low fuser temperature |
|
E003 |
Low fuser temperature |
|
E010 |
Drive |
|
E030 |
Counter |
|
E080 |
Color change board problems |
|
E081 |
Color horizontal motor problem |
|
E082 |
Color horizontal motor problem |
|
E083 |
Color problem in vertical direction |
|
E084 |
Color problem in vertical direction |
|
E085 |
Color problem in vertical direction |
|
E086 |
Color unit claw release problem |
|
E089 |
Color change incomplete |
|
E100 |
Laser problem |
|
E110 |
Laser motor problem |
|
E140 |
Laser unit |
|
E203 |
Scan drive problem |
|
E210 |
Lens not home or won't leave home |
|
E240 |
DC controller |
|
E401 |
Document feeder pick up motor |
|
E402 |
Document feeder belt motor |
|
E403 |
RADF feed motor |
|
E404 |
Document feeder motor |
|
E411 |
Document feeder sensor |
|
E500 |
Sorter to DC control interface problem |
|
E510 |
Stapler/sorter motor |
|
E530 |
Stapler swing motor |
|
E531 |
Stapler swing motor |
|
E540 |
Sorter bin motor |
|
E541 |
Sorter bin motor |
|
E710 |
DC controller |
|
E711 |
DC controller |
|
E712 |
DC controller to document feeder interface problem |
Canon 6012F
| Код ошибки | Описание | ||
| C | No problem. Means that the machine is correcting the fuser film tracking | ||
| CC | Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier | ||
| E000 | Low fuser temperature | ||
| E001 | High fuser temperature | ||
| E002 | High fuser temperature | ||
| E003 | Erratic fuser temperature | ||
| E007 | Fuser film off track and will not repair itself | ||
| E010 | Main drive problem | ||
| E030 | Counter problem | ||
| E064 | Scan problem, or power supply | ||
| E202 | Scan problem | ||
| E210 | Lens drive problem or lens sensor | ||
| E220 | Exposure lamp stays on or off | ||
| E240 | DC controller (main board) or composite power supply | ||
| E261 | Zero cross problem. Power frequency or composite power supply | ||
| E400 | Communication problem between boards | ||
| E803 | 24 volt problem | ||
| EO | Fuser problem | ||
| H | Fuser overheat |
Fuser temperature not rising at
|
Код ошибки |
Описание |
|
E000 |
Fuser did not heat up |
|
E001 |
Fuser temperature too high |
|
E002 |
Fuser temperature not rising at correct pace |
|
E003 |
Fuser temperature drops |
|
E004 |
SSR shorted |
|
E210 |
Lens home problem |
|
E212 |
Lens home problem |
|
E220 |
Exposure lamp problem |
|
E224 |
Blank shutter home problem |
|
E240 |
DC controller or composite power supply problem |
|
E400 |
Data communication problem |
|
E401 |
Pickup motor problem |
|
E402 |
Belt motor problem |
|
E403 |
Feeder motor |
|
E404 |
Delivery motor |
|
E411 |
Document detect sensor |
|
E500 |
Communication problem with copier |
|
E510 |
Feeder motor |
|
E530 |
Home sensor |
|
E531 |
Staple swing sensor problem |
|
E540 |
Bin shift motor rotation problem |
|
E541 |
Bin motor |
|
E710 |
DC controller |
|
E711 |
Document feeder IC failure |
|
E716 |
Cassette feed IC failure |
|
E800 |
Auto power-off circuit problem |
|
E901 |
Cassette feed motor |
|
E902 |
Paper guide home sensor problem |
Fuser did not heat up.
|
Код ошибки |
Описание |
|
E000 |
Fuser did not heat up. Lamp, thermal switch, thermistors, connections, AC driver, DC controller, SSR, etc |
|
E001 |
Fuser temperature too high. Same possibilities as E000, as well as shorted wire |
|
E002 |
Fuser temperature not rising at correct pace. Same possibilities as E000 |
|
E003 |
Fuser temperature drops. Same as E003 |
|
E004 |
Fuser problem. AC driver, SSR bad, wire shorted |
|
E010 |
Drive problem. Main motor, gears, etc |
|
E030 |
Total counter |
|
E064 |
Composite power board or DC controller |
|
E065 |
Composite power board or DC controller |
|
E202 |
Scan motor or scan sensor problem. Panel locked with no Код ошибки. Scan motor problem |
|
E203 |
Scan problem or scan sensor |
|
E204 |
Scan problem or scan sensor |
|
E210 |
Lens sensor or motor problem |
|
E212 |
Lens sensor or motor problem |
|
E220 |
Exposure lamp or exposure lamp regulator board |
|
E224 |
Blanking shutter motor or sensor |
|
E240 |
DC controller or composite power supply problem |
|
E244 |
DC controller |
|
E400 |
RDF to copier communication problem |
|
E401 |
RDF Pickup motor or pick up sensor |
|
E403 |
RDF feed motor or pulse sensor |
|
E404 |
RDF delivery motion problem |
|
E404 |
RDF delivery motor problem |
|
E411 |
RDF tray sensor or registration sensor |
|
E500 |
Sorter main board or communication with copier |
|
E510 |
Sorter feed motor |
|
E530 |
Sorter guide bar motor |
|
E531 |
Sorter stapler motor |
|
E540 |
Sorter bin shift motor |
|
E541 |
Sorter bin motor |
|
E550 |
Sorter power supply |
|
E710 |
DC controller |
|
E711 |
DC controller |
|
E712 |
Document feeder IC failure |
|
E716 |
DC controller. Sorter |
|
E800 |
Auto power off function (DC controller) |
|
E901 |
Pedistal motor |
|
E902 |
Jogger side plate sensor or motor |
Fuser did not heat up.
|
Код ошибки |
Описание |
|
E000 |
Fuser did not heat up. Lamp, thermal switch, thermistors, connections, AC driver, DC controller, SSR, etc |
|
E001 |
Fuser temperature too high. Same possibilities as E000, as well as shorted wire |
|
E002 |
Fuser temperature not rising at correct pace, same possibilities as E000 |
|
E003 |
Fuser temperature drops. Same as E000 |
|
E004 |
Fuser problem: AC driver, SSR bad, wire shorted |
|
E005 |
Fuser cleaning web, or problem with sensor, lever or connector. Service mode 6 is the probably reset for this |
|
E006 |
Fuser feed connector |
|
E010 |
Drive problem. Main motor, gears, etc |
|
E013 |
Waste toner drive problem, or waste toner sensor switch has been actuated too many times |
|
E015 |
Pickup motor power supply. Could be bad motor or motor board, or DC controller |
|
E020 |
Problem with developer unit, toner hopper, hopper motor, connection, sensor or DC controller |
|
E030 |
Total counter |
|
E031 |
Option counter or total counter |
|
E050 |
Holding tray (duplex) home position sensor motor or board |
|
E051 |
Holding tray (duplex) home sensor motor or board |
|
E202 |
Panel locked up, but might be no Код ошибки, scan motor problem |
|
E203 |
Scan problem or scan sensor |
|
E204 |
Scan problem or scan sensor |
|
E210 |
Lens sensor or motor problem |
|
E212 |
Lens sensor or motor problem |
|
E213 |
Scan lock sensor or lock solenoid |
|
E220 |
Exposure lamp regulator board |
|
E240 |
DC controller or composite power supply problem |
|
E243 |
DC controller |
|
E400 |
RDF to copier communication problem |
|
E401 |
RDF pickup motor or pickup sensor |
|
E402 |
RDF belt motor or pulse sensor |
|
E403 |
RDF feed motor or pulse sensor |
|
E411 |
RDF tray sensor or registration sensor |
|
E500 |
Sorter main board or communication with copier |
|
E510 |
Sorter feed motor |
|
E522 |
Sorter push bar motor |
|
E523 |
Sorter reference wall motor |
|
E524 |
Sorter multi-guide motor |
|
E525 |
Sorter bin paper sensor automatic adjustment problem |
|
E526 |
Sorter bin paper sensor automatic adjustment problem |
|
E530 |
Sorter guide bar motor |
|
E531 |
Sorter stapler motor |
|
E532 |
Stapler motor |
|
E533 |
Stapler inside paper sensor |
|
E540 |
Sorter bin shift motor |
|
E550 |
Sorter power supply |
|
E710 |
DC controller |
|
E711 |
DC controller |
|
E712 |
Document feeder IC failure |
|
E713 |
DC controller, sorter |
|
E800 |
Auto power off circuit problem. Main switch or DC controller |
|
E802 |
Auto power off circuit problem. Main switch or DC controller |
the upper fixing roller does
|
Код ошибки |
Описание |
|
E000 |
After power-on, the upper fixing roller does not reach 100 C within 5 min |
|
E001 |
The temperature of the upper fixing roller exceeds 230 C for 5 sec or more |
|
E002 |
After the temperature of the upper fixing roller has exceeded 100 C, it does not reach 180 C within 5 min |
|
E003 |
After the temperature of the upper fixing roller has reached 180 C, it drops to 100 C or less for 5 sec or more |
|
E005 |
The length used of the cleaning belt inside the fixing assembly has exceeded a specific value |
|
E012 |
After the drum motor drive signal has been generated, clock pulses are not generated within 2 sec |
|
E013 |
After the waste toner feeding screw has become locked, the detecting switch (SW20) is pressed a multiple number of times within a specific period of time |
|
E014 |
When the fixing motor (M17) is rotating, an error is detected for 2 sec or more |
|
E015 |
After the pick up motor drive signal has been generated, clock pulses have not been generated within 2 sec |
|
E019 |
As many as 50,000 have been made after detecting a waste toner full condition |
|
E020 |
During copying, the toner supply signal is 0', indicating the absence of toner, for 3 min or more. During toner supply sequence at time of installation, the toner supply signal does not go '1' after 6 min or more |
|
E030 |
After the total copy counter has turned OFF, an open circuit is detected for the total copy counter |
|
E032 |
After the clock pulse signal reached the IPC communication format of the copier DC controller PCB, the Copy Data Controller-A1 does not detect the signal |
|
E050 |
While the paper jogging guide motor (M11) drive signal is being generated, the paper guide home position signal (THP) is not generated for 2 sec or more. While the paper jogging guide motor (M11) is being generated, the paper jogging guide home position signal (THP) is generated for two sec or more |
|
E202 |
The scanner home position signal (SCHP) is not generated within 10 sec after the power switch or the Copy Start Key is pressed |
|
E203 |
While the scanner motor drive signal is being generated, clock pulses are not generated within 2 sec |
|
E204 |
The scanner leading edge signal (SCDP1) is not generated within 0.8 sec after the scanner has started to move |
|
E209 |
The scanner C.F.F. position signal (SCFFP) is not generated within 10 sec after the C.F.F. has been sent |
|
E210 |
The lens X home position signal (SCFFP) is not generated within 10 sec after the C.F.F. has been sent |
|
E212 |
The lens Y home position signal (LYHP) is not generated within 9 sec after the power switch or the Copy Start Key is turned ON. The lens Y home position signal (LYHP) is generated for 2 sec or more |
|
E213 |
In stream reading mode, the scanner original leading edge sensor 2 signal (SCDP2) is not generated for 5 pages continuously |
|
E214 |
While the scanner cooling fan (FM1, FM10, FM11) is rotating, an error signal is generated for 2 sec or more |
|
E270 |
In stream reading mode, the scanner leading edge signal(SCDP2) is not generated within a specific period of time after a command has been issued to lock the scanner |
|
E710 |
At power-on the IPC (Q170) on the DC controller PCB cannot be initialized |
|
E711 |
After power-on the IPC (Q170) on the DC controller PCB goes out of order |
|
E712 |
The communication IC on the RDF controller PCB has gone out of order |
|
E713 |
The communication IC on the sorter control PCB has gone out of order |
|
E715 |
The communication IC on the C.F.F. controller PCB has gone out of order |
|
E717 |
The communication IC on the Copy Data Controller-A1 PCB has gone out of order |
|
E800 |
An open circuit is detected |
|
E801 |
Current flows from the activation circuit in the absence of the scanning lamp ON signal |
|
E802 |
The relay (RL3) in the power supply unit does not operate in spite of the auto power-off signal |
Toner motor, toner level sensor,
|
Код ошибки |
Описание |
|
E000 |
Thermistor |
|
E001 |
SSR |
|
E002 |
Thermistor, ht. Lamp thermal fuse or SSR |
|
E003 |
Thermistor, ht. Lamp thermal fuse or SSR |
|
E005 |
Fuser cleaning belt |
|
E010 |
Main drive problem |
|
E020 |
Toner motor, toner level sensor, toner hopper sensor |
|
E030 |
Counter |
|
E050 |
Duplex problem |
|
E203 |
Scan home problem |
|
E210 |
Lens home sensor |
|
E401 |
Document feeder paper pickup motor |
|
E402 |
Document feeder belt clock pulse problem |
|
E403 |
Document feeder main motor clock pulse problem |
|
E411 |
Document feeder sensor problem |
|
E500 |
Sorter/copier interface problem |
|
E510 |
Sorter motor drive |
|
E530 |
Sorter home sensor |
|
E531 |
Stapler swing sensor |
|
E540 |
Sorter lead cam home sensor |
|
E541 |
Sorter lead cam home sensor |
|
E710 |
DC controller board |
|
E711 |
DC controller board |
|
E712 |
Document feeder problem |
No problem. Means that the
|
Код ошибки |
Описание |
|
C |
No problem. Means that the machine is correcting the fuser film tracking. |
|
CC |
Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier. |
|
E000 |
Low fuser temperature |
|
E001 |
High fuser temperature |
|
E002 |
High fuser temperature |
|
E003 |
Erratic fuser temperature |
|
E007 |
Fuser film off track and will not repair itself |
|
E010 |
Main drive problem |
|
E030 |
Counter problem |
|
E064 |
Scan problem, or power supply |
|
E202 |
Scan problem |
|
E210 |
Lens drive problem or lens sensor |
|
E220 |
Exposure lamp stays on or off |
|
E240 |
DC controller (main board) or composite power supply |
|
E261 |
Zero cross problem. Power frequency or composite power supply |
|
E400 |
Communication problem between boards |
|
E803 |
24 volt problem |
|
EO |
Fuser problem |
|
H |
Fuser overheat |
Fuser did not heat up.
|
Код ошибки |
Описание |
|
E000 |
Fuser did not heat up. Lamp, thermal switch, thermistors, connections, AC driver, DC controller, SSR, etc |
|
E001 |
Fuser temperature too high. Same possibilities as E000, as well as shorted wire |
|
E002 |
Fuser temperature not rising at correct pace. Same possibilities as E000 |
|
E003 |
Fuser temperature drops. Same as E003 |
|
E004 |
Fuser problem. AC driver, SSR bad, wire shorted |
|
E010 |
Drive problem. Main motor, gears, etc |
|
E030 |
Total counter |
|
E064 |
Composite power board or DC controller |
|
E065 |
Composite power board or DC controller |
|
E202 |
Scan motor or scan sensor problem. Panel locked with no Код ошибки. Scan motor problem |
|
E203 |
Scan problem or scan sensor |
|
E204 |
Scan problem or scan sensor |
|
E210 |
Lens sensor or motor problem |
|
E212 |
Lens sensor or motor problem |
|
E220 |
Exposure lamp or exposure lamp regulator board |
|
E224 |
Blanking shutter motor or sensor |
|
E240 |
DC controller or composite power supply problem |
|
E244 |
DC controller |
|
E400 |
RDF to copier communication problem |
|
E401 |
RDF Pickup motor or pick up sensor |
|
E403 |
RDF feed motor or pulse sensor |
|
E404 |
RDF delivery motion problem |
|
E404 |
RDF delivery motor problem |
|
E411 |
RDF tray sensor or registration sensor |
|
E500 |
Sorter main board or communication with copier |
|
E510 |
Sorter feed motor |
|
E530 |
Sorter guide bar motor |
|
E531 |
Sorter stapler motor |
|
E540 |
Sorter bin shift motor |
|
E541 |
Sorter bin motor |
|
E550 |
Sorter power supply |
|
E710 |
DC controller |
|
E711 |
DC controller |
|
E712 |
Document feeder IC failure |
|
E716 |
DC controller. Sorter |
|
E800 |
Auto power off function (DC controller) |
|
E901 |
Pedistal motor |
|
E902 |
Jogger side plate sensor or motor |
Toner motor, toner level sensor,
|
Код ошибки |
Описание |
|
E000 |
Thermistor |
|
E001 |
SSR |
|
E002 |
Thermistor, ht. Lamp thermal fuse or SSR |
|
E003 |
Thermistor, ht. Lamp thermal fuse or SSR |
|
E005 |
Fuser cleaning belt |
|
E010 |
Main drive problem |
|
E020 |
Toner motor, toner level sensor, toner hopper sensor |
|
E030 |
Counter |
|
E050 |
Duplex problem |
|
E203 |
Scan home problem |
|
E210 |
Lens home sensor |
|
E401 |
Document feeder paper pickup motor |
|
E402 |
Document feeder belt clock pulse problem |
|
E403 |
Document feeder main motor clock pulse problem |
|
E411 |
Document feeder sensor problem |
|
E500 |
Sorter/copier interface problem |
|
E500 |
An error is identified in the communication between the sorter and the copier |
|
E510 |
The clock signal from the motor is absent for 250ms or more |
|
E510 |
Sorter motor drive |
|
E513 |
The clock signal from the motor is absent for 250 ms or more |
|
E530 |
Sorter home sensor |
|
E530 |
The home position sensor (P17) fails to go OFF when an equivalent of 2560 pulses of the motor drive command has been generated |
|
E531 |
The stapler unit swing sensor (MS9) fails to go ON within 500 ms after the motor drive command has been generated. MS9 fails to go back OFF within 1000 ms after it has gone on |
|
E531 |
Stapler swing sensor |
|
E540 |
The lead cam home position sensor (P12) fails to go OFF within 2000 ms after the motor drive command has been generated. P12 fails to go back ON within 2000 ms after it has gone OFF |
|
E540 |
Sorter lead cam home sensor |
|
E541 |
Sorter lead cam home sensor |
|
E710 |
DC controller board |
|
E711 |
DC controller board |
|
E712 |
Document feeder problem |
Heater triac, DC controller, AC
|
Код ошибки |
Описание |
|
E000 |
Heater (Reset by unplugging machine) |
|
E001 |
Heater triac, DC controller, AC driver (reset by unplugging) |
|
E005 |
Fuser cleaner belt at end. Replace |
|
E010 |
Main motor, DC controller or DC driver board |
|
E011 |
Any motor ( main, scan, cleaner belt, duplex, toner, lens) DC driver, DC controller, duplex driver board |
|
E020 |
Toner out signal has been sent for at least 3 minutes |
|
E050 |
Duplex |
|
E203 |
Scan motor, DC driver, DC controller |
|
E210 |
Lens home sensor not actuated or won't deactuate |
|
E240 |
Controller board |
|
E241 |
Controller board |
|
E242 |
Controller board |
|
E400 |
DC controller, Doc. Feeder board, 24V power supply |
|
E500 |
DC controller, sorter board, 24V power supply |
Heater triac, DC controller, AC
|
Код ошибки |
Описание |
|
E000 |
Heater (Reset by unplugging machine) |
|
E001 |
Heater triac, DC controller, AC driver (reset by unplugging) |
|
E005 |
Fuser cleaner belt at end. Replace |
|
E010 |
Main motor, DC controller or DC driver board |
|
E011 |
Any motor ( main, scan, cleaner belt, duplex, toner, lens) DC driver, DC controller, duplex driver board |
|
E020 |
Toner out signal has been sent for at least 3 minutes |
|
E050 |
Duplex |
|
E203 |
Scan motor, DC driver, DC controller |
|
E210 |
Lens home sensor not actuated or won't deactuate |
|
E240 |
Controller board |
|
E241 |
Controller board |
|
E242 |
Controller board |
|
E400 |
DC controller, Doc. Feeder board, 24V power supply |
|
E500 |
DC controller, sorter board, 24V power supply |
Fuser problem. Temperature too low.
|
Код ошибки |
Описание |
|
E000 |
Fuser problem. Temperature too low. Heat lamp, thermal fuse or thermoswitch, thermistor, triac etc |
|
E001 |
Fuser problem. Temperature too high. Probably triac |
|
E005 |
Fuser web finished |
|
E005 |
Fuser cleaner belt user up |
|
E010 |
Drive |
|
E010 |
Main drive problem |
|
E011 |
Drive problem. Could be main motor, scan motor, cleaning web motor or duplex motor |
|
E020 |
Toner empty sensor sees no toner added for 3 min probably toner feed problem |
|
E050 |
Duplex problem |
|
E203 |
Scan motor |
|
E210 |
Lens home sensor or lens won't leave home |
|
E240 |
DC controller board |
|
E241 |
DC controller board |
|
E242 |
DC controller board |
|
E243 |
Operation panel board |
|
E400 |
DC controller, ADF board or 24V |
|
E500 |
DC controller, sorter board or 24V |
|
E510 |
Finisher; feed motor, pulse sensor, finisher board |
|
E520 |
Finisher; stack motor, stack tray sensor, finisher board |
|
E530 |
Finisher; guide plate motor, stapler guide, finisher board |
|
E531 |
Finisher; staple motor, staple sensor, finisher board |
The surface temperature of the
|
Код ошибки |
Описание |
|
E000 |
The surface temperature of the fixing assembly upper roller fails to rise by a specified value within 90 sec after power-on. The surface temperature of the fixing assembly upper roller fails to reach 150C within 8 min after power on. The surface temperature of the fixing assembly upper roller fails to reach 180C within 5 min after it has reached 150C. The surface temperature of the fixing assembly upper roller falls below 50C in standby |
|
E001 |
The surface temperature of the fixing assembly upper roller exceeds 250C |
|
E005 |
The cleaning belt inside the fixing assembly has been taken up more than a specified length |
|
E010 |
After generation of the main motor drive signal, two or more pulses are not received within 2 sec |
|
E020 |
The accumulative time during which the toner supply signal (TSP) has been generated by the developing assembly reaches 3 min |
|
E050 |
The holding tray home position signal (THP) is not generated within 4 sec while the holding tray motor drive signal (TMDP1,2) is being generated. The holding tray home position signal (THP) is generated 1 sec or more while the holding tray motor drive signal (TMDP1.2) is being generated |
|
E13 |
The error detection circuit on the waste toner feed motor driver PCB has detected on overcurrent |
|
E203 |
Input of two or more clock pulses is not received within 2 sec from the scanner motor drive signal is generated |
|
E210 |
The lens home position signal (LHP) is not generated within 4.8 sec after the power switch or door switch has gone ON. The lens home position signal (LHP) is generate 2 sec or more |
|
E240 |
An error has occurred in the microprocessor on the DC controller PCB |
|
E243 |
An error has occurred in the communication between the microprocessor of the DC controller PCB and the microprocessor in the control panel |
|
E710 |
An error has occurred in the communication between the DC controller PCB and the controller PCB of the option, and the DC controller has detected the error |
The surface temperature of the
|
Код ошибки |
Описание |
|
E000 |
The surface temperature of the fixing assembly upper roller fails to rise by a specified value within 90 sec after power-on. The surface temperature of the fixing assembly upper roller fails to reach 150C within 8 min after power-on |
|
E001 |
The surface temperature of the fixing assembly upper roller exceeds 250C |
|
E005 |
The cleaning belt inside the fixing assembly has been taken up more than a specified length |
|
E010 |
After generation of the main motor drive signal, two or more pulses are not received within 2 sec |
|
E013 |
The error detection circuit on the waste toner feed motor driver PCB has detected an overcurrent |
|
E020 |
The accumulative time during which the toner supply signal (TSP) has been generated by the developing assembly reaches 3 min* |
|
E050 |
The holding tray home position signal (THP) is not generated within 4 sec while the holding tray motor drive signal (TMDP1, 2) is being generated. The holding tray home position signal (THP) is generated 1 sec or more while the holding tray motor drive signal (TMDP1, 2) is being generated |
|
E203 |
Input of two or more clock pulses is not received within 2 sec from the scanner motor drive signal is generated |
|
E210 |
The lens home position signal (LHP) is not generated within 4.8 sec after power switch or door switch has gone ON. The lens home position signal (LHP) is generate 2 sec or more |
|
E240 |
An error has occurred in the microprocessor on the DC controller PCB |
|
E243 |
An error has occurred in the microprocessor of the DC controller PCB and the microprocessor in the control panel |
|
E710 |
An error has occurred in the communication between the DC controller PCB and the controller PCB of the option, and the DC controller has detected the error |
|
E712 |
No communication is perceived from the RF controller PCB for 200 ms or more the communication is monitored at all times |
An error is identified in
|
Код ошибки |
Описание |
|
E500 |
An error is identified in the communication between the sorter and copier |
|
E510 |
The clock signal from the motor is absent for 250 ms or more |
|
E513 |
The clock signal from the motor is absent for 250 ms or more |
|
E530 |
The home position sensor (P17) fails to go OFF when an equivalent of 2560 pulses of the motor drive command has been generated |
|
E531 |
The stapler unit swing sensor (MS9) fails to go ON within 500 ms after the motor drive command has been generated. MS9 fails to go back OFF within 1000 ms after it has gone ON |
|
E540 |
The lead cam home position sensor (P12) fails to go OFF within 2000 ms after the motor drive command has been generated. P12 fails to go back ON within 2000 ms after it has gone OFF |
No problem. Means that the
|
Код ошибки |
Описание |
|
C |
No problem. Means that the machine is correcting the fuser film tracking |
|
CC |
Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier |
|
E000 |
Low fuser temperature |
|
E001 |
High fuser temperature |
|
E002 |
High fuser temperature |
|
E003 |
Erratic fuser temperature |
|
E007 |
Fuser film off track and will not repair itself |
|
E010 |
Main drive problem |
|
E030 |
Counter problem |
|
E064 |
Scan problem, or power supply |
|
E202 |
Scan problem |
|
E210 |
Lens drive problem or lens sensor |
|
E220 |
Exposure lamp stays on or off |
|
E240 |
DC controller (main board) or composite power supply |
|
E261 |
Zero cross problem. Power frequency or composite power supply |
|
E400 |
Communication problem between boards |
|
E803 |
24 volt problem |
|
E0 |
Fuser problem |
|
H |
Fuser overheat |
Fuser thermistor, thermal fuse or
|
Код ошибки |
Описание |
|
E000 |
Fuser thermistor, heater, thermal fuse |
|
E001 |
Fuser thermistor, or triac |
|
E002 |
Fuser thermistor, thermal fuse or triac |
|
E003 |
Fuser thermistor, heater, thermal fuse or triac |
|
E004 |
Triac or fuser won't shut off |
|
E007 |
Fuser film is off center or not driving properly |
|
E010 |
Main motor drive problem |
|
E030 |
Counter |
|
E064 |
Composite power supply or main board |
|
E202 |
Scan problem |
|
E210 |
Lens drive problem |
|
E220 |
Exposure lamp |
|
E240 |
Main board or composite power supply |
|
E261 |
Composite power supply or fluctuating power |
|
E400 |
ADF communication problem to machine |
|
E402 |
ADF belt motor drive |
|
E404 |
ADF exit motor |
|
E411 |
ADF document detect, or registration sensor or edge sensor |
|
E500 |
Sorter communication problem |
|
E510 |
Sorter drive problem |
|
E530 |
Stapler guide bar motor |
|
E531 |
Stapler swing motor |
|
E540 |
Bin shift motor |
|
E541 |
Bin motor drive problem |
|
E710 |
Main board |
|
E711 |
Main board |
|
E712 |
Main board or communication problem with ADF |
|
E717 |
Main board, asst. board |
|
U0 |
Initializing. Sets all user modes to factory default settings |
|
U1 |
Auto clear timer. Range 1-9. Each digit=1 minute |
|
U2 |
Automatic power shut off timer |
|
U3 |
Fine adjustment of zoom |
|
U4 |
Auto cassette switching |
|
U5 |
Sort or non-sort default |
|
U6 |
Cleans document feeder pickup assembly |
|
U7 |
CLEAR "replace drum" |
|
U9 |
Auto exposure or manual exposure as default |
Fuser problem. Low temperature. Lamp,
|
Код ошибки |
Описание |
|
E000 |
Fuser problem. Low temperature. Lamp, thermal switch, AC driver |
|
E001 |
Fuser problem. High temperature. Triac, AC driver, pinched wire |
|
E004 |
Fuser problem |
|
E0053 |
Sorter |
|
E030 |
Counter |
|
E202 |
Scan |
|
E210 |
Lens |
|
E221 |
Exposure lamp regulator board, thermal fuse, exposure lamp |
|
E400 |
Automatic document feeder |
|
E500 |
Sorter |
|
E710 |
DC controller |
Canon C200D
| Код ошибки | Описание | ||
| E000 | Fuser thermistor, heater thermal fuse | ||
| E001 | Fuser thermistor, or triac | ||
| E002 | Fuser thermistor, thermal fuse or triac | ||
| E003 | Fuser thermistor, heater, thermal fuse or triac | ||
| E004 | Triac or fuser won't shut off | ||
| E007 | Fuser film is off center or not driving properly. Might be able to reset in service mode 4-407 | ||
| E010 | Main motor drive problem | ||
| E030 | Counter | ||
| E041 | Paper deck motor, clutch or sensor | ||
| E064 | Composite power supply or main motor board | ||
| E202 | Scan problem. Motor sensor | ||
| E210 | Lens drive problem | ||
| E220 | Exposure lamp | ||
| E240 | Main board or composite power supply | ||
| E260 | Main board, power supply cooling fan or composite power supply | ||
| E261 | Composite power supply or fluctuating power | ||
| E400 | ADF communication to machine | ||
| E401 | ADF pickup motor or sensor | ||
| E402 | ADF belt motor drive | ||
| E403 | ADF feed motor or slip sensor | ||
| E404 | ADF exit motor | ||
| E411 | ADF document detect, or registration sensor or edge sensor | ||
| E500 | Sorter communication problem | ||
| E510 | Sorter drive problem | ||
| E530 | Stapler guide bar motor | ||
| E531 | Stapler swing motor | ||
| E540 | Bin shift motor | ||
| E541 | Bin motor drive problem | ||
| E710 | Main board (DC controller.) | ||
| E711 | Main board (DC controller.) | ||
| E712 | Main board or communication problem with ADF, or ADF main board | ||
| E717 | Main board, assist board. "Replace drum": Drum waste toner is full, or drum has run 40,000 copies. Reset with user | ||
| E802 | Composite power supply or DC controller | ||
| E901 | Cassette feed unit board or cassette feed motor | ||
| E902 | Horizontal registration problem. I think this refers to the duplex section | ||
| J1 | Feed jam | ||
| J10 | Duplex exit jam | ||
| J11 | Vertical jam | ||
| J12 | Vertical jam | ||
| J13 | Vertical jam | ||
| J14 | Vertical jam | ||
| J15 | Deck jam | ||
| J2 | Feed jam | ||
| J3 | Separation area jam | ||
| J4 | Separation area jam | ||
| J5 | Exit jam | ||
| J6 | Exit jam | ||
| J7 | Sorter jam | ||
| J8 | Door open jam | ||
| J9 | Cassette jam | ||
| JA | Cassette jam | ||
| Jb | Cassette jam | ||
| JC | Cassette jam | ||
| Jd | Duplex feed jam | ||
| JE | Duplex exit jam | ||
| JF | Duplex registration jam |
The main thermistor reading does
|
Код ошибки |
Описание |
|
E000 |
The main thermistor reading does not reach 40oC 14 sec after the fixing heater goes ON (fixing low temperature error) |
|
E001 |
The main thermistor reading reaches 220°C or higher (fixing high temperature error) |
|
E002 |
A start-up fault is detected under any of the following conditions of the main thermistor (start-up detection fault): after exceeding 40°C, it fails to reach 60°C within 10 sec. after exceeding 60°C, it fails to reach 80°C within 10 sec. . . . after exceeding 180°C, it fails to reach 195°C within 10 sec. |
|
E003 |
After the end of the WAIT period, the main thermistor reading is 100°C or lower. In standby, the sub thermistor reading is 50°C or lower. (low temperature error in fixing temperature control) |
|
E004 |
At time of initialization, the ZEROXI* signal of the power supply is not detected. During temperature control, the ZEROXI* signal does not arrive for 3 sec continuously. A short circuit is detected in the triac (ASIC; fixing temperature control drive circuit error). Possible cause: Fixing assembly is faulty. (The main thermistor has an open circuit. The sub thermistor has an open circuit. The fixing heater has an open circuit. The power supply PCB is faulty. The DC controller PCB is faulty.) |
|
Note: If E000 through E004 is indicated, the RAM on the image processor will retain the error memory of the fixing assembly after the power switch has been turned off an then on. Execute the following in service mode, and turn off and then on the power switch to clear the memory: #7 PRINTER - #4 PRINTER RESET - YES=(*) |
|
|
E010 |
A specific revolution is not detected from the main motor rotation detection signal (MLOK*), causing the signal to go '1' (main motor fault) Possible cause: The main motor (M101) is faulty. The controller PCB is faulty. |
|
E100 |
When the scanner motor is started up, the BD input signal does not arrive within a specific period of time. When the scanner motor is started up, the motor rotation is too fast, and fails to reach a specific revolution within 20 sec at time of deceleration. While the scanner motor is rotating at a specific speed, the BD input signal cycle is not within a specific range (±2%) for an equivalent of 10 mm (print distance). While the scanner motor is rotating at a specific speed, the BD input signal cycle is not as indicated (±2%). During the WMUPR period after the power switch has been turned on or the front cover/left cover has been opened/closed, the drum unit is absent. Possible cause: The wiring is faulty (short circuit, open circuit). The laser scanner unit is faulty. The DC controller PCB is faulty. The drum unit is not installed. |
|
E719 |
The communication between the card reader and the image processor PCB is disrupted. Possible cause: The wiring is faulty (short circuit, open circuit). The card reader is faulty. The image processor PCB is faulty. |
|
Note: If E719 is indicated, the fault in communication is retained by the RAM on the image processor even when the power switch has been turned off and then on; be sure to execute #12 CLEAR - CARD in service mode before making corrections. |
|
|
E805 |
After the heat discharge fan drive signal is generated, the fan lock detection signal does not arrive for a specific period of time. Possible cause: The fan wiring is faulty (short circuit, open circuit). The heat discharge fan (FM101) is fautly. The DC controller PCB is faulty. |
|
Finisher Error Codes |
|
|
E500 |
An error has occurred in the communication between the machine and the finisher twice continuously. Possible cause: The harness to the finisher is faulty (disconnected connector, open circuit). The finisher controller PCB or the DC controller PCB is faulty. |
|
E514 |
The stack delivery belt does not reach home position when the stack handling motor (M2) is driven for a specific time (CW; if the same condition occurs during stack delivery, a jam will be identified). Possible cause: The stack handling motor (M2) is faulty. The stack delivery home position sensor (S8) is faulty. The connector is disconnected or has an operation circuit. The stack handling motor relay harness is faulty. The stack delivery belt is faulty. The finisher controller PCB is faulty. |
|
E530 |
The rear aligning plate does not reach home position when the rear alignment motor (M4) has been driven for a specific time. The rear aligning plate does not reach home position when the rear alignment motor (M4) has been driven for a specific time. Possible cause: The rear alignment motor (M4) is faulty. The rear aligning plate home position sensor (S7) is faulty. The sensor connector is disconnected or has an open circuit. The rear alignment motor relay harness is faulty. The rear aligning plate is subjected to an abnormal load. The finisher controller PCB is faulty. |
|
E531 |
The stapler does not leave the stapling home position sensor (S13) within 0.5 sec after the stapler motor (M6) is rotated CW. The stapler does to return to the home position sensor (S13) within 0.5 sec after the stapler motor (M6) is driven CW and, in addition, it does not return to the sensor within 0.5 sec after the motor is driven CCW thereafter. Possible cause: The stapler motor (M6) is faulty. The stapler home position sensor (SW1) is faulty. The stapler harness is faulty. The finisher controller PCB is faulty. |
|
E537 |
The front aligning plate does not reach home position when the front aligning motor (M3) is driven for a specific time. The front aligning plate does not leave home position when the front alignment motor (M3) is driven for a specific time. Possible cause: The front alignment motor (M3) is faulty. The front aligning plate home position sensor (S6) is faulty. The sensor connector is disconnected or has an open circuit. The front alignment motor relay harness if faulty. The front aligning plate is subjected to an abnormal load. The finisher controller PCB is faulty. |
|
E551 |
The delivery fan rotation signal (FNALCOK) does not arrive within 1 sec when the heat discharge fan drive signal (FANON) is sent. Possible cause: The heat discharge fan (FM1) is faulty. The heat discharge fan relay harness is faulty. The heat discharge fan is subjected to an abnormal load. The finisher controller PCB is faulty. |
|
E577 |
The return roller does not reach home position when the delivery motor (M1) is driven for a specific time. (If the same condition is detected while alignment takes place in the direction of feed, a jam will be identified) Possible cause: The delivery motor (M1) on the finisher controller PCB is faulty. The return roller home position sensor (S3) is faulty. The connector is discontented or has an open circuit. The delivery motor relay harness is faulty. The return roller is faulty. The finisher controller PCB is faulty. |
|
E580 |
The stack tray upper limit sensor (S1) goes ON while the stack tray up/down motor (M5) is in operation. The clock signal of the stack tray up/down clock sensor (S9) is not detected 15 times or more within 0.8 sec while the stack tray up/down motor (M5) is in operation. It does not reach the stack tray paper height sensor (S10) 2 sec after the stack tray up/down motor (M5) rotates for ascent. It does not leave the stack tray power height sensor (S10) 2 sec after the stack tray up/down motor (M5) starts to rotate for descent. Possible cause: The stack tray up/down motor (M5) is faulty. The stack tray paper height sensor (S10) is faulty. The sensor connector is disconnected or has an open circuit. The stack tray up/down clock sensor (SW9) is faulty. The sensor connector is disconnected or has an open circuit. The stack tray up/down motor is subjected to an abnormal load. The finisher controller PCB is faulty. |
|
E585 |
The stack retaining lever does not reach home position when the stack handling motor (M2) has been driven for a specific time (at the start of motor CCW rotation). (If the same condition is detected during stack delivery, a jam will be identified) Possible cause: The stack handling motor (M2) is faulty. The stack delivery lever home position sensor (S8) is faulty. The sensor connector is disconnected or has an open circuit. The stack handling motor relay harness is faulty. The stack retaining lever is faulty. The finisher controller PCB is faulty. |
Canon NP
| Код ошибки | Описание | ||
| E000 | Fuser thermistor, heater thermal fuse | ||
| E001 | Fuser thermistor, or triac | ||
| E002 | Fuser thermistor, thermal fuse or triac | ||
| E003 | Fuser thermistor, heater, thermal fuse or triac | ||
| E004 | Triac or fuser won't shut off | ||
| E007 | Fuser film is off center or not driving properly. Might be able to reset in service mode 4-407 | ||
| E010 | Main motor drive problem | ||
| E030 | Counter | ||
| E041 | Paper deck motor, clutch or sensor | ||
| E064 | Composite power supply or main motor board | ||
| E202 | Scan problem. Motor sensor | ||
| E210 | Lens drive problem | ||
| E220 | Exposure lamp | ||
| E240 | Main board or composite power supply | ||
| E260 | Main board, power supply cooling fan or composite power supply | ||
| E261 | Composite power supply or fluctuating power | ||
| E400 | ADF communication to machine | ||
| E401 | ADF pickup motor or sensor | ||
| E402 | ADF belt motor drive | ||
| E403 | ADF feed motor or slip sensor | ||
| E404 | ADF exit motor | ||
| E411 | ADF document detect, or registration sensor or edge sensor | ||
| E500 | Sorter communication problem | ||
| E510 | Sorter drive problem | ||
| E530 | Stapler guide bar motor | ||
| E531 | Stapler swing motor | ||
| E540 | Bin shift motor | ||
| E541 | Bin motor drive problem | ||
| E710 | Main board (DC controller.) | ||
| E711 | Main board (DC controller.) | ||
| E712 | Main board or communication problem with ADF, or ADF main board | ||
| E717 | Main board, assist board. "Replace drum": Drum waste toner is full, or drum has run 40,000 copies. Reset with user | ||
| E802 | Composite power supply or DC controller | ||
| E901 | Cassette feed unit board or cassette feed motor | ||
| E902 | Horizontal registration problem. I think this refers to the duplex section | ||
| J1 | Feed jam | ||
| J10 | Duplex exit jam | ||
| J11 | Vertical jam | ||
| J12 | Vertical jam | ||
| J13 | Vertical jam | ||
| J14 | Vertical jam | ||
| J15 | Deck jam | ||
| J2 | Feed jam | ||
| J3 | Separation area jam | ||
| J4 | Separation area jam | ||
| J5 | Exit jam | ||
| J6 | Exit jam | ||
| J7 | Sorter jam | ||
| J8 | Door open jam | ||
| J9 | Cassette jam | ||
| JA | Cassette jam | ||
| Jb | Cassette jam | ||
| JC | Cassette jam | ||
| Jd | Duplex feed jam | ||
| JE | Duplex exit jam | ||
| JF | Duplex registration jam |
Low temperature, thermoswitch, thermistor or
|
Код ошибки |
Описание |
|
E000 |
Low temperature, thermoswitch, thermistor or AC driver |
|
E001 |
High temperature, thermistor, AC driver |
|
E030 |
Counter |
|
E202 |
Scan not returning home. Scan not leaving home |
|
E221 |
Lamp regulator board |
|
E400 |
Document feeder problem |
|
E500 |
Sorter problem |
has poor contact or an
|
Код ошибки |
Описание |
|
E000 |
? The thermistor (TH1, TH2) has poor contact or an open circuit ? The fixing heater (H1) has an open circuit ? The thermal switch (TSW1) has turned on ? The triac is faulty ? The DC controller PCB is faulty |
|
E001 |
? The thermistor (TH1, TH2) has a short circuit ? The triac is faulty ? The DC controller PCB is faulty |
|
E002 E003 |
The thermistor (TH1, TH2) has poor contact or an open circuit ? The fixing heater (H1) has an open circuit ? The thermal switch (TSW1) has turned on ? The triac is faulty ? The DC controller PCB is faulty |
|
E004 |
? The triac has a short circuit ? The DC controller PCB is faulty |
|
E010 |
? The main motor (M1) is faulty ? The DC controller PCB is faulty |
|
E013 |
? The waste toner feedscrew is locked ? The waste toner feedscrew lock sensor (PS8) is faulty ? The DC controller PCB is faulty |
|
E030 |
? The total copy counter has an open circuit ? The DC controller PCB is faulty |
|
E031 |
? The accessories counter has an open circuit ? The DC controller PCB is faulty |
|
(E202) |
No code indication. Keys are disabled ? The scanner home position sensor (PS1) is faulty ? The scanner motor (M2) is faulty ? The DC controller PCB is faulty |
|
E208 |
? The mirror home position sensor (PS3) is faulty ? The mirror motor (M4) is faulty ? The DC controller PCB is faulty |
|
E210 |
? The lens home position sensor (PS2) is faulty ? The lens motor (M3) is faulty ? The DC controller PCB is faulty |
|
E220 |
? The lamp regulator PCB is faulty ? The DC controller PCB is faulty |
|
E261 |
? The power supply frequency is faulty ? The power supply PCB is faulty |
|
E710 E711 |
? The DC controller PCB is faulty |
|
E712 |
? The DC controller PCB is faulty ? The ADF controller PCB is fault ? The ADF cable is faulty |
|
E717 |
? The DC controller PCB is faulty ? The Remote Diagnostic Device II PCB is faulty |
|
E800 |
? The auto power-off circuit has an open circuit ? The DC controller PCB is faulty |
|
E805 |
? The exhaust fan (FM2, FM4) is faulty ? The DC controller PCB is faulty |
|
E821 |
? The ozone filter is clogged ? The cleaner thermistor (TH3) has poor contact or an open circuit ? The DC controller PCB is faulty |
Canon PC
| Код ошибки | Описание | ||
| C | No problem. Means that the machine is correcting the fuser film tracking | ||
| CC | Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier | ||
| E000 | Low fuser temperature | ||
| E001 | High fuser temperature | ||
| E002 | High fuser temperature | ||
| E003 | Erratic fuser temperature | ||
| E007 | Fuser film off track and will not repair itself | ||
| E010 | Main drive problem | ||
| E030 | Counter problem | ||
| E064 | Scan problem, or power supply | ||
| E202 | Scan problem | ||
| E210 | Lens drive problem or lens sensor | ||
| E220 | Exposure lamp stays on or off | ||
| E240 | DC controller (main board) or composite power supply | ||
| E261 | Zero cross problem. Power frequency or composite power supply | ||
| E400 | Communication problem between boards | ||
| E803 | 24 volt problem | ||
| EO | Fuser problem | ||
| H | Fuser overheat | ||
| E000 | Fuser thermistor, heater, thermal fuse | ||
| E001 | Fuser thermistor, or triac | ||
| E002 | Fuser thermistor, thermal fuse or triac | ||
| E003 | Fuser thermistor, heater, thermal fuse or triac | ||
| E004 | Triac or fuser won't shut off | ||
| E007 | Fuser film is off center or not driving properly | ||
| E010 | Main motor drive problem | ||
| E030 | Counter | ||
| E064 | Composite power supply or main board | ||
| E202 | Scan problem | ||
| E210 | Lens drive problem | ||
| E220 | Exposure lamp | ||
| E240 | Main board or composite power supply | ||
| E261 | Composite power supply or fluctuating power | ||
| E400 | ADF communication problem to machine | ||
| E402 | ADF belt motor drive | ||
| E404 | ADF exit motor | ||
| E411 | ADF document detect, or registration sensor or edge sensor | ||
| E500 | Sorter communication problem | ||
| E510 | Sorter drive problem | ||
| E530 | Stapler guide bar motor | ||
| E531 | Stapler swing motor | ||
| E540 | Bin shift motor | ||
| E541 | Bin motor drive problem | ||
| E710 | Main board | ||
| E711 | Main board | ||
| E712 | Main board or communication problem with ADF | ||
| E717 | Main board, asst. board | ||
| U0 | Initializing. Sets all user modes to factory default settings | ||
| U1 | Auto clear timer. Range 1-9. Each digit=1 minute | ||
| U2 | Automatic power shut off timer | ||
| U3 | Fine adjustment of zoom | ||
| U4 | Auto cassette switching | ||
| U5 | Sort or non-sort default | ||
| U6 | Cleans document feeder pickup assembly | ||
| U7 | CLEAR "replace drum" | ||
| U9 | Auto exposure or manual exposure as default | ||
| EO | Heater problem | ||
| E1 | The heater film has gone off center. Turn machine off & on, make sure it's level etc | ||
| E2 | Scan problme | ||
| E6 | Exposure lamp or exposure lamp sensor | ||
| E000 | Fuser problem | ||
| E001 | Fuser problem | ||
| E010 | Drive | ||
| E210 | Zoom/lens/motor problem | ||
| E00 | Heater, thermoswitch, exit sensor (Reset by jumping CP102 pins 1 & 2, or leave machine off for 20 seconds | ||
| E001 | Shorted thermistor or high-temperature, Exit sensor | ||
| E010 | Clock Pulse | ||
| E210 | Zoom Lens Problem |
Canon PC6
|
Код ошибки |
Описание |
|
E000 |
Fuser problem |
|
E001 |
Fuser problem |
|
E010 |
Drive |
|
E210 |
Zoom/lens/motor problem |
Reset by jumping CP102 pins
|
Код ошибки |
Описание |
|
E00 |
Heater, thermoswitch, exit sensor ( Reset by jumping CP102 pins 1 & 2, or leave machine off for 20 seconds |
|
E001 |
Shorted thermistor or high-temperature, Exit sensor |
|
E010 |
Clock Pulse |
|
E210 |
Zoom Lens Problem |
Что такое Девелопер?
Девелопер, он же носитель - ферромагнитный порошок, используемый в двухкомпонентных машинах для переноса тонера из DV-бокса (developer-box) на поверхность фотобарабана. Если быть совершенно точным, то на поверхность магнитного вала DV-бокса, а оттуда тонер уже под воздействием электростатических сил перетягивается на фотобарабан; причем сам девелопер, в силу своих магнитных свойств, остается на магнитном валу (прим. автора: здесь и далее используется терминология фирмы Sharp, у других разработчиков названия и некоторые детали могут немного отличаться, но суть от этого не меняется).
По структуре девелопер представляет собой мелкие шарики ферромагнитного материала. Это хорошо чувствуется, если потоптаться на рассыпанном порошке: нога заметно скользит. В дешевых аппаратах с одноразовыми картриджами девелопер представляет собой мелкие кристаллики неправильной формы. Разность в структуре объясняется тем, что в многоразовых картриджах использование дешевого "кристаллического" девелопера приведет к быстрому износу всех соприкасающихся с ним деталей (так называемый "абразивный эффект"). В одноразовых картриджах долгий срок жизни в принципе не нужен, здесь главное – себестоимость. Каждая частичка девелопера имеет специальное покрытие (жесткое резиноподобное для "одноразовых" девелоперов или полимерное стеклоподобное для "долгосрочных" порошков), благодаря которому при трении в процессе перемешивания девелопера его частички электризуются, что делает их способными удерживать также наэлектризованные частички тонера.
Кстати, теперь становится понятным, почему девелопер "пылит" в конце срока службы. Из-за длительного перемешивания он попросту "теряет" покрытие на своих частицах и уже не может удерживать тонер; причем при обедненной смеси этот процесс происходит быстрее. Кроме того, при длительном хранении, особенно при неблагоприятных условиях, в покрытии частичек девелопера образуются микротрещины, вследствие чего долго хранившийся порошок имеет более короткий срок службы.
Блок проявки в двухкомпонентых машинах состоит из двух бункеров (или боксов) – тонер-бокса и DV-бокса. При нормальных условиях в тонер-боксе находится тонер, в DV-боксе – смесь тонера и девелопера в определенной концентрации. При работе копира происходит расход тонера (на фотобарабане проявляется видимое изображение – отсюда и название "блок проявки") из DV-бокса; следовательно, меняется и концентрация тонера в DV-боксе. Когда содержание тонера в смеси снизится до определенного значения, происходит подмешивание (добавление) тонера из тонер-бокса в DV-бокс, пока не восстановится исходное, запомненное в памяти копира, значение концентрации.
Количество тонера в DV-боксе измеряется датчиком концентрации. Принцип его работы – изменение индуктивности при взаимодействии катушки с внешним ферромагнитным веществом. Опять же, если быть более точным, измеряется не количество тонера в смеси, а именно девелопера, т.к. тонер в основе своей полимер и на изменение индуктивности никак не влияет. Просто в смеси тонер как бы "разжижает" девелопер, отчего меняются ферромагнитные свойства последнего.
С теорией вроде как покончено, перейдем к практике.
Даже в заводских условиях практически невозможно с ювелирной точностью от партии к партии повторить параметры порошка, поэтому уже на заводе подбирается оптимальное соотношение смеси девелопер-тонер именно для данной партии девелопера, обеспечивающее требуемое качество изображения. И девелопер поставляется уже с добавленным в него тонером. Далее, уже при инсталляции девелопера на копире, считывается вот это "заводское" оптимальное значение концентрации и запоминается в памяти машины.
Из сказанного следует, что не рекомендуется делать следующее:
Копировать на машине с новым, только что засыпанным, девелопером до прогонки инсталляционной программы, ибо нарушается оптимальная заводская концентрация.
Прогонять программу инсталляции без нужды, т.е. без замены девелопера на новый, ибо одному Богу известно, какая концентрация имеется в текущий момент.
При включении копира (и в процессе работы, естественно) проверяется соответствие концентрации реальной и запомненной, и если тонера в DV-боксе мало (или машине кажется, что мало), то она пытается восстановить запомненную концентрацию, подмешивая тонер. Отсюда следует, что если Вам необходимо заменить девелопер, а в памяти копира по какой-либо причине записано неправильное значение концентрации (см. п.п.1 и 2 выше), либо имеется подозрение на неисправность датчика концентрации и его цепей, нужно успеть войти в сервисный режим до момента, когда машина начнет "восстанавливать" концентрацию. Либо, чтобы быть спокойным, можно вытрясти тонер-бокс, чтобы случайно не нарушить заводскую концентрацию.
Из сказанного следует и то, что для исправной и настроенной машины абсолютно все равно, инсталлируете ли Вы девелопер с пустым или заполненным тонер-боксом, т.к. в процессе прогона инсталляционной программы подмеса тонера не происходит. Точно так же для машины все равно, если Вы правильно проинсталлируете девелопер, а потом сделаете несколько десятков копий с пустым тонер-боксом; главное, что машина уже запомнила нужное значение. Как только Вы добавите тонер (или вставите тубу с тонером и т.д.), копир сам подмешает нужное ему количество.
Все вышесказанное верно для машин с датчиками концентрации. Есть копиры, где таких датчиков нет, а используются другие методы для определения количества подмешиваемого тонера в процессе работы. Наверняка у других производителей могут применяться и другие методики инсталляции носителя. Но про это пусть рассказывают представители этих брэндов, у них это лучше получится.
P.S. На последних цифровых копирах формата А4 и младшего сегмента формата А3 Sharp отказался от программы инсталляции девелопера, т.е. для начала работы девелопер просто засыпается в бункер без каких-либо дополнительных операций. Связано это с упрощением процедуры запуска аппаратов, т.к. предназначены они в первую очередь для индивидуальных пользователей и малых офисов.Да и фабрика в состоянии контролировать стабильность качества рабочей смеси в достаточной степени.
Для старших сегментов программная инсталляция сохранилась, т.к. требования к качеству копий выше.
http://www.repair-printer.ru/viewtopic.php?t=2809
